Where Is The Curt Q24 5th Wheel Trailer Hitch Manufactured

Question

Question:

Where is the Curt Q24 manufactured?

asked by: Stephen P

0

Expert Reply:

Hey Stephen,

All Curt 5th wheel trailer hitches, including the # C16545-16017, are manufactured in China. I've attached a link to one of our help articles below that lists where manufacturers produce their hitches. If you're wanting an American made 5th wheel trailer hitch then you'll want the B&W Companion # BWRVK3305 instead.

expert reply by: Kevin C

0

Answer 1

The replacement lens that you are looking for is the (discontinued) Clearance Light Replacement Lens #59 Red 34-59-010 from Bargman which has 4" L x 2" W x 5/8" H dimensions just like you have. Attached is a review video for you to…

view full answer...

Answer 2

If the OEM brake controller on your 2014 Ram pickup is operating properly then you don't "need" an aftermarket controller. With that being said, the OEM controllers aren't as reliable as aftermarket options so it may not be a bad…

view full answer...

Answer 3

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Where Is The Curt Q24 5th Wheel Trailer Hitch Manufactured

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching