Replacement Hitch Install Hardware for Draw Tite # 75782

Question

Question:

I went to put this draw tite hitch on my inherited car.parents 2015 Ford escape. They bought a hitch years ago for a scooter but never had anyone install it. I have it but cannot find the hardware. Any chance I can buy just the hardware kit?

asked by: Ryan B

0

Expert Reply:

We do sell replacement hardware for all of the hitches we carry with the part # RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

expert reply by: Jameson C

0

Ryan

3/16/2024

So #RHK ardware kit is for my hitch or every hitch?

Reply

Jameson C.

3/18/2024

@Ryan Not to be confusing...but yes and yes. It's a part number in our system that we use as a replacement hardware kit for all of the hitches we carry. But when you go to order it you just need to input the hitch part number that you have and we'll make sure you get the correct hardware for your hitch.

Reply

Answer 1

Most Vehicles and hitches have their own specific hardware to insure proper fit and towing capacity. Our #C13149 hitch includes a hardware kit and installation guide. I attached a video on the installation for your convenience. The hardware specs can…

view full answer...

Answer 2

I would be happy to help! To replace the hardware used to install your trailer hitch receiver on your new 2021 Honda CR-V you will need the Replacement Hardware Kit #RHK. When on the product page you will select the manufacturer of the hitch you…

view full answer...

Answer 3

In order to obtain the replacement hardware for the Curt Trailer Hitch Receiver part #C13105 on your 2017 Toyota Sienna you will need to use the Replacement Hardware Kit for Trailer Hitches part #RHK. Once you arrive at the product page you will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

We do sell replacement hardware for all of the hitches we carry with the part #RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...