Recommendation for Roadmaster Front and Rear Sway Bars for a 2005 Fleetwood Bounder 34F

Question

Question:

Hi, can you advise me correct model front and rear sway bars for a 2005 Fleetwood Bounder 34F built on a Workhorse W22 chassis? Many thanks,

asked by: Mike S

0

Expert Reply:

Yes I can!

For a front sway bar to fit your 2005 Fleetwood Bounder 34F built on a Workhorse W22 chassis you would want the Roadmaster Front Sway Bar part # RM-1259-105 and for a rear sway bar you would want the part # RM-1259-108.

I confirmed these fits with Roadmaster so they will work very well for your vehicle.

expert reply by: Jameson C

0

Answer 1

When installing the Roadmaster Front Anti-Sway Bar and TruTrac Rod Kit #RM-1259-106 you will want those brackets sit flush; you can enlarge the hole or drill a new one so that you can get the bracket sitting flush to the rail. My contact over at…

view full answer...

Answer 2

The Roadmaster Rear Anti-Sway Bar for Motorhomes #RM-1139-143 can use your factory u-bolts if they are long enough. If they are not, then Roadmaster recommends using the 7/8 inch diameter u-bolts that are longer (most likely the larger diameter due…

view full answer...

Answer 3

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 8

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 11

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 12

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...