Does Draw Tite Hitch # 76134 Have Second Hole for J-Pin Anti-Rattle

Question

Question:

Does this hitch come with a j-pin hole?

asked by: Alex Z

0

Expert Reply:

The Draw Tite hitch part # 76134 does not come with a second hole near the hitch pin hole to be used with a J-pin anti-rattle device. You'd need to use it with an anti rattle like the # 63232 which fits into hollow shank hitch accessories.

expert reply by: Jameson C

0

Answer 1

Both the RidgeBack #Y02459 and FullTilt #Y02463 are high-end hanging-style racks from Yakima but in this case the FullTilt has a few extra features so I recommend going that route. Both racks have very similar features as far as tilting/folding ease…

view full answer...

Answer 2

The easiest way to determine which bolt you'll need is by locating which Yakima model you've got. You should be able to locate the model of rack from a sticker somewhere on the lower half of the mast or on the hitch shank-but sometimes those…

view full answer...

Answer 3

There is an SKS lock end that works with the #8890260 with the part #Y07235 but by the time you add up the cost of both parts you are better off going with a similar universal setup like the #63232 since the price is better and would work just as…

view full answer...

Answer 4

In order to replace the bolt for the Yakima DoubleDown 4 Bike Rack, you need to look at the Replacement Hardware for Yakima Doubledown Hitch Mounted Bike Rack #Y8890206. •Replacement hardware for Doubledown 2, 4 and 5 •Includes: (1) bolt, (2) flat…

view full answer...

Answer 5

For me there is one clear choice between the two bike racks you asked about, and for one very particular reason - convenience. Due to how convenient it is, I definitely recommend the RidgeBack, which is the following part number: - Yakima RidgeBack…

view full answer...

Answer 6

The Yakima LockUp Hitch Lock and Cable Lock Item #Y07238 appear to be the same as its counterpart on the Yakima site SKU: #8007238. In regards to a red piece at the end of the lock the Yakima DeadLock Hitch Lock and Integrated Locking Cable has been…

view full answer...

Answer 7

When it comes to The Swagman Cable Lock #S64030 it will not work properly with your Yakima Double Down because it has a different thread pattern on the lock. You would have to use The Yakima LockUp Hitch Lock and Cable Lock - Same Key System #Y07238.…

view full answer...

Answer 8

We may have the correct replacement hitch bolt for you, but they are specific to both manufacturers as well as racks, so the Saris hitch bolt you mentioned won't work for your Yakima 2-bike rack. There are a number of options for you, and to get…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...