Velcro Strip Quantity in Replacement Truxedo Shur-Bond Velcro Brand Fastener Kit # TX1115174

Question

Question:

Does the package contain a new strip for both rails or is there only one strip per package quantity? Do I need to order qty 2 or 1 to be able to do both rails. 2007 Chevrolet Silverado crew cab

asked by: Josh

0

Expert Reply:

The Replacement Truxedo Shur-Bond Velcro Brand Fastener Kit # TX1115174 comes with 2 of the hook-side Velcro fasteners that attach to the truck rails so you will need one kit. The mating (loop) pieces will already be on the tonneau cover. This kit also includes a set of 3 replacement rivets (only 2 are needed, one is a spare). Each of these Velcro strips measure 80-inches long x 1-5/16-inches wide.

We also offer part # TX1115173 for 8-foot beds; these Velcro strips measure 96-inches long x 1-1/4-inches wide.

expert reply by: Adam R

0

Answer 1

Truxedo offers the replacement Velcro strips part #TX1115174 that will fit the original Edge tonneaus they offer. This would be the kit you would need.

view full answer...

Answer 2

The replacement Velcro-like fastener strips for your TruXedo Lo Pro QT tonneau cover on your 2010 Dodge Ram 1500 can be found listed as the Replacement TruXedo Shur-Bond Velcro Brand Fastener #TX1115174 on our site. The fastener is 80 inches long and…

view full answer...

Answer 3

The Replacement TruXedo Shur-Bond Velcro Brand Fastener for 6-1/2' Beds -1-5/16" Wide #TX1115174 is designed to fit TruXedo Lo Pro or Original Edge tonneau covers. While I can't say for sure whether or not these will fit a Tonno Pro I…

view full answer...

Answer 4

Yes, Replacement TruXedo Shur-Bond Velcro Brand Fastener #TX1115174 slides into the rail on TruXedo Lo Pro QT or Original Edge tonneau covers. It is 80 inches long at 1-5/16 inches wide.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...