Tools Needed to Install Enclosed Trailer Transition Plate

Question

Question:

what tools are needed to install this transition plate?

asked by: Jack

0

Expert Reply:

Here is a list of the tools needed to install the etrailer Enclosed Trailer Transition Plate # e32JR:

- Tape Measure
- Drill
- Hex Drive Socket Adapter
- 10mm Socket
- 13mm Socket

I have also added a link below to the instructions of the # e32JR for you to take a look at.

expert reply by: Kyle S

0

Answer 1

The etrailer Enclosed Trailer Transition Plate #e32JR will work very well for loading and unloading motorcycles. It has a working load limit of 1,000 lbs so even with your 850 lb bike, you are well within parameters weight capacity wise. Especially…

view full answer...

Answer 2

In regards to the etrailer Enclosed Trailer Transition Plate #e32JR, the end plates are not designed to be swapped. There are pre-drilled holes in the end plates and center plates, which would not line up correctly if the end plates were swapped.…

view full answer...

Answer 3

Yes, you can cut the hinge, #H300, to the size you need with the proper equipment. An angle grinder with a cutting wheel would be a good choice to cut the hinge. We have other hinge options if you are interested. I have linked them for you.

view full answer...

Answer 4

Here is a list of the tools needed to install the etrailer Enclosed Trailer Transition Plate #e32JR: - Tape Measure - Drill - Hex Drive Socket Adapter - 10mm Socket - 13mm Socket I have also added a link below to the instructions of the #e32JR for…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hey Scott you will need to get the width of your ramp as well as the weight of the ramp to pick out what you'd need. For example the part #M394FR is for 8 foot wide ramps and has a weight capacity of 185 lb. I attached a link to all of the…

view full answer...

Answer 9

I do see the 2024 Ford Transit 350 is unchanged from the 2023 model year so there should be no reason the SumoSprings Solo Custom Helper Springs #SSR-121-54. When I reached out to SumoSprings they have not yet been able to verify fitment yet as they…

view full answer...

Answer 10

I verified with the manufacturer for you that the thickness of the RV Vinyl Flooring - Diamond Pattern - 24' Long x 8'2" Wide Strip - Black #TS89FR is .075 inches

view full answer...

Answer 11

Yes, the Kenda Karrier ST175/80R13 Radial Trailer Tire #AM31990 will indeed fit on the etrailer Hitch Mounted Spare Tire Carrier #e98ZR. The spare tire carrier will work with virtually any 4 lug, 5 lug or 6 lug wheel. The #AM31990 wheel uses the…

view full answer...

Answer 12

Hey Lou, so the install of the Conventional Ramp Door Spring part #362SA7218 is something that should be done by someone who has experience winding garage springs. The amount of turns or preload will be the amount that gives you the correct amount of…

view full answer...

Tools Needed to Install Enclosed Trailer Transition Plate

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching