Recommended Replacement Handle and Pin for a RAM 8000 Series Jack

Question

Question:

I’m searching for the Handle and pin for the RAM 8000 series

asked by: Raymond B

0

Expert Reply:

For your RAM 8000 Series jack # TJD-7000S, you can use the Replacement Sidewind Handle for etrailer and Ram Square, Direct Weld Jacks # TJD-7000S-HD for a replacement handle and handle pin.

If by pin you were actually referring to the footplate keeper pin, then you'd need the Replacement Footplate Keeper Pin for etrailer and Ram Square, Direct Weld Jacks # TJD-7000-PN as well.

expert reply by: Bryce D

0

Answer 1

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 2

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 3

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 4

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 5

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 6

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 7

The etrailer.com Trailer Hub and Drum Assembly #AKHD-655-6-EZ-K referenced in your question is designed for 5,200 or 6,000 pound axles. The weight capacity of the hub itself (for a single hub) is 3,000 pounds. As long as your current hubs use the…

view full answer...

Answer 8

To check the fit and compatibility for a set of replacement hydraulic drum brakes on your M101A military dump trailer you will want to match up a few things. Those things are drum dimensions, axle weight capacity, mounting bolt pattern and the…

view full answer...

Answer 9

The equalizer of a tandem axle trailer is not the balance point of the trailer. I would recommend putting the wheel chocks of your trailer as far forward as you can in the trailer. This will help prevent any potential sway that can occur from not…

view full answer...

Answer 10

When securing your motorcycle inside your enclosed 12 foot long trailer using a chock like the Tow-Rax #TWSPWM the most important factor to consider is the trailer's tongue weight. You will just want to make sure that its tongue weight with the…

view full answer...

Answer 11

The overload warning you are seeing indicates that the P3, #90195, detects an excessive current overload condition during operation. This means that there is most likely a short in the brake output wire. The P3 has diagnostic troubleshooting…

view full answer...

Recommended Replacement Handle and Pin for a RAM 8000 Series Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching