Is Dexter Hub 84545UC1-EZ Sold in Pairs or Individually

Question

Question:

Is this qty one hub or two?

asked by: Scott

1

Helpful Expert Reply:

The Dexter trailer axle # 84545UC1-EZ that you mentioned is sold individually. If you needed two you would need to order a quantity of two.

expert reply by: Jameson C

1

Answer 1

Sounds like your spindle has a tang washer like the part #5-101 based on what you described. This is a very common washer setup for trailer axles. I attached a picture that shows what it looks like installed as well.

view full answer...

Answer 2

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 3

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 4

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a #L68149 inner bearing and #L44649…

view full answer...

Answer 5

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 6

Hi Keith; the Dexter 8-248 uses standard bearings for a 3,500 lb axle. If you want a hub and drum assembly the #AKHD-545-35-EZ-K you were looking at will fit. The direct Dexter replacement for the idler hub is the #84545BX or if you want it…

view full answer...

Answer 7

In order to determine the correct replacement hubs for your trailer I will need to know the inner and outer bearing numbers stamped into the sides of the bearings. If the axle has a grease zerk fitting at the end then it is an EZ lube axle. If there…

view full answer...

Answer 8

The correct replacement for your Dexter 8-248 trailer hub is the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles #84545BX that you referenced.

view full answer...

Answer 9

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 10

In most cases, a 3,700 lb axle will use the same bearings and seal as a 3,500 lb axle which means you can use any hub for a 3,500 lb axle on a 3,700 lb axle. The bearings for a 3,500 lb axle are L68149 for the inner, L44649 for the outer, and the…

view full answer...

Answer 11

Yes, I can confirm that the 24x40 etrailer Cargo Carrier for RV Bumper #e99050 does include the bumper safety struts #MO22FR you're referencing.

view full answer...

Answer 12

You will want either the CE Smith Galvanized #CE13315 or Black #CE13311 idler hub assemblies. These both have the 1-1/16" ID bearings #L44649 and include grease seals for your 1-1/4" spindle diameter.

view full answer...

Is Dexter Hub 84545UC1-EZ Sold in Pairs or Individually

Product Page this Question was Asked From

Continue Researching