Replacement Hub Assembly for T.D.E. 11033

Question

Question:

what is the part # for a replacement hub assembly for the T.D.E. Part # 11033?

asked by: Josh Y

1

Helpful Expert Reply:

From what I was able to find out from my research, the Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles. Replacement hubs that have these specs typically use a # L68149 inner bearing and # L44649 outer bearing, as well as inner race # L68111 , outer race # L44610 and grease seals with inner diameter of 1.719" and outer diameter of 2.565".

You'll want to verify that your current hubs have these bearings, races and seals to ensure that a replacement hub will fit on your spindle. If you do have those components, a good replacement hub assembly to replace your T.D.E. 11033 hub with those components is the Trailer Idler Hub Assembly for 3500-lb Axles # AKIHUB-545-35-PG-K . This kit comes with the bearings, races, seal, grease cap, and lug nuts included and is a pre-greased hub so you won't need to worry about dealing with packing and greasing the bearings.

expert reply by: Erik B

1

click to enlarge

Mike

5/24/2020

that hub assembly part# does not turn up anything

Reply

Chris R.

5/27/2020

The 11033 hub model mentioned above is specific to Tie-Down Engineering. We don't carry this exact hub assembly. If your hub uses the above-mentioned bearings and has a 5 on 4-1/2" bolt pattern though the etrailer.com # AKHD-545-35-EZ-K will work perfectly as a replacement.

Reply

Answer 1

I believe we can narrow this down based on the information you are referencing. However, the best way to be sure is to measure your existing bearings or spindle with a digital caliper like the #PTW80157. It looks like one bearing is stamped with…

view full answer...

Answer 2

The Tie Down Engineering 11033 hub has a 5 on 4-1/2" bolt pattern and is designed for 3500-lb axles like the #AKIHUB-545-35-K. Then for a spindle the part #TRU84FR that you referenced would be what you need.

view full answer...

Answer 3

I believe you meant a TDE 46245, is that correct? If that's the case, you've got a 3500 lb axle which uses a 10 inch hub/rotor with a 5 on 4-1/2 wheel bolt pattern. You'll want to use the Kodiak #KHR10D hub/rotor as a…

view full answer...

Answer 4

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 5

You will want either the CE Smith Galvanized #CE13315 or Black #CE13311 idler hub assemblies. These both have the 1-1/16" ID bearings #L44649 and include grease seals for your 1-1/4" spindle diameter.

view full answer...

Answer 6

Based on the spindle your trailer has the hub part #AKIHUB-545-35-K is going to fit on it despite it having what looks like a different design overall.

view full answer...

Answer 7

The Easy Grease Trailer Idler Hub Assembly part #AKIHUB-545-35-EZ-K will be an excellent replacement option for your TDE 3,750 Lb Axle. The bearings and seals are the same for both 3,500 lb and 3,750 lb axles and it has a 5 on 4-1/2" bolt…

view full answer...

Answer 8

According to my research, your trailer will have a 3500 lb axle on it. The replacement for your TDE 11033 hubs should be #AKIHUB-545-35-G-EZ-K, which use an L68149 inner and an L44649 outer wheel bearing along with a 58846 grease seal that has a…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

For your 2 inch by 2 inch axles you would want a Redline Spindle for Square Axles #TRU47FR. This is a square spindle designed for 2 inch square axles so it should work for well for you. Check out the review video I attached. The EZ Lube Spindle…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

Your trailer axle is likely rated for 3,500 lbs which means you need the following parts: - Hydraulic Brake Kit - Uni-Servo - Free Backing #AKFBBRK-35-D - Easy Grease Trailer Hub/Drum Assembly #AKHD-545-35-G-EZ-K for 5 on 4-1/2" bolt pattern -…

view full answer...

Replacement Hub Assembly for T.D.E. 11033

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching