What Screws Are Needed To Install 60" Horse Trailer Vinyl Pad?

Question

Question:

Im looking at purchasing the 60inch vinyl pad and need to know what screw is recommended for mounting onto a steel trailer/divider.

asked by: Shawnessy

0

Expert Reply:

The Trailer Horse Pad Screw # PS-8 will allow you to install the 60" Horse Trailer Side Pad # HTP1260BK on your steel trailer/divider. This screw is 3/4" long and will require a 1/8" pilot hole on your steel trailer. I recommend using at least 24 screws which will allow you to place them roughly every 6" on center to hold it in place.

expert reply by: Bud M

0

Answer 1

They are different in width. Aside from that and price everything else is the same. The Horse Trailer Side Pad item #HTP1260BK measures 60" long x 12" wide x 2" thick. The Horse Trailer Side Pad item #HTP60BK measures…

view full answer...

Answer 2

In order to install the the Horse Trailer Side Pad - 60" #HTP1260BK you just need to screw them in. What you'll need are the Trailer Horse Pad Screw #PS-8 and attach them to the sides of the pad.

view full answer...

Answer 3

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as…

view full answer...

Answer 4

For screws to attach the part #HTP24BK to your horse trailer we recommend the part #PS-8. These screws are 3/4 of an inch long so I would go with a plywood thickness of at least 1/2 of an inch.

view full answer...

Answer 5

We have added the 60" X 12" Pad #HTP1260BK since the particular answer page you found was made. We do have the 40" X 9" Pad #HTP40BK and 60" X 9" Pad #HTP60BK. These are all made by Redline with Redneck Trailer Supply…

view full answer...

Answer 6

Yes, the 60" Horse Trailer Side Pad #HTP1260BK is essentially a universal option so you can install it wherever you're wanting to as long as you have the space for it. You'll need to pick up #8 x 3/4" sized screws for this…

view full answer...

Answer 7

Though we do have the Horse Trailer Side Pad #HTP1260BK that is 60" x 12", the widest 40" option we have will only be 9" ( #HTP40BK). What is going to be your best bet is to go with the Horse Trailer Escape Door Pad #HTP12BK,…

view full answer...

Answer 8

The Horse Trailer Side Pad - 60" #HTP1260BK will allow you to remove staples from the cardboard backing and wrap the cover around plywood as you referenced. You will simply want to be careful in removing the staples so you don't damage the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Screws Are Needed To Install 60" Horse Trailer Vinyl Pad?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching