Recommended Screws for the Horse Trailer Pad HTP24BK

Question

Question:

What thickness of plywood would you recommend to mount these on before attaching them to inside of trailer? and what would be a suggestion on what screws or bolts to use in order to mount them to metal sided trailer any help would be greatly appreciated. .thanks

asked by: George S

0

Expert Reply:

For screws to attach the part # HTP24BK to your horse trailer we recommend the part # PS-8. These screws are 3/4 of an inch long so I would go with a plywood thickness of at least 1/2 of an inch.

expert reply by: Jameson C

0

Answer 1

The Trailer Horse Pad Screw #PS-8 will allow you to install the 60" Horse Trailer Side Pad #HTP1260BK on your steel trailer/divider. This screw is 3/4" long and will require a 1/8" pilot hole on your steel trailer. I…

view full answer...

Answer 2

They are different in width. Aside from that and price everything else is the same. The Horse Trailer Side Pad item #HTP1260BK measures 60" long x 12" wide x 2" thick. The Horse Trailer Side Pad item #HTP60BK measures…

view full answer...

Answer 3

In order to install the the Horse Trailer Side Pad - 60" #HTP1260BK you just need to screw them in. What you'll need are the Trailer Horse Pad Screw #PS-8 and attach them to the sides of the pad.

view full answer...

Answer 4

The PS-8 screws should work very well going into either material you mentioned. The threads are coarse enough that they'll get good hold on the aluminum or the rubber. For best results, you'll want to ensure that as many screws as…

view full answer...

Answer 5

Our horse trailer pad items such as 60-inch Side Pad #HTP60BK and 24-inch Breast Pad #HTP24BK don't come with included hardware because the requirements between different trailers can vary so much depending on the type of material the pads…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The difference between load ranges varies based on the tire size and brand. When comparing two tires of the same size and brand, a load range D tire will always have a greater weight capacity and psi rating than a load range C. However, when…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Recommended Screws for the Horse Trailer Pad HTP24BK

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching