Question About a Product

Question

Question:

I do not have a factory trailer connector. Do I need Curt PN C55377 to add one to my van. 2001 GMC Savana custom.

asked by: Frank H

0

Expert Reply:

Yes, you do. The Curt T-Connector Vehicle Wiring Harness item # C55377 is exactly what you need to add a 4-way connector to your 2001 GMC Savana Van. This custom-fit T-connector plugs into your van's wiring harness, which is located behind the interior trim panels in your rear cargo area.

I have linked the installation instructions below.

expert reply by: Jerred H

0

Answer 1

I do have a solution for you, however the Curt T-Connector Vehicle Wiring Harness #55540 referenced in your question is designed to fit the 2003 to present Chevy Express Vans. This wiring harness will not work on your 2001 model. For your 2001…

view full answer...

Answer 2

You can check behind the Express van's passenger side trim panel in the rear cargo area to see if it has connection points for factory replacement wiring. Factory 4-pole items #118240 and #C55240 both use the same type of square connector, shown…

view full answer...

Answer 3

The center pin on your 7-way on the trailer side is the reverse light function. These can be different colors, which I get is confusing, but you will need to do some deductive reasoning or use a circuit tester to determine the function and color. For…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Question About a Product

Product Page this Question was Asked From

Continue Researching