Replacement Front and Middle Jacks for an 8,000 lb. Capacity Lippert Level Up Leveling System

Question

Question:

I have a 2013 raptor 5th wheel. leaking front and middle auto adjust lippert jacks. the front has mounting holes half way down and the middle has them all the way bottom to top. I dont see the one with half the mount with hole just the one with hole all the way.

asked by: Kurt M

1

Helpful Expert Reply:

The Replacement Lippert Level Up Hydraulic Jack # LC26FR that you found is the correct option for the front jacks and the Replacement Hydraulic Jack Assembly for Lippert Level Up System # LC36VR is the correct option for the middle jacks. These are the correct jacks if your system is the 8,000 lb. capacity Level Up system.

I know the jacks do not have the holes only half way down, but the # LC26FR is still the right front jack option.

expert reply by: Scott S

1

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver #DT57YR is our highest capacity receiver for your 2023 Honda HR-V. This receiver has a maximum tongue weight rating of 300lbs but be sure to verify you do not exceed any weight capacities given by Honda.…

view full answer...

Answer 2

Your Tundra uses a Yakima roof rack. You'll need a replacement SkyLine tower, part #8880614.

view full answer...

Answer 3

Yes it does! When Adco designed the AquaShed #290-52258 they accounted for any rooftop accessories like your AC units. There is some extra material built-in to make sure that the entire cover fits like a glove plus they have integrated zippers so you…

view full answer...

Answer 4

Hey Mason, I wasn't able to find anything relating to that part number but basically you're going to need to pick a ball that has the correct ball diameter (1 7/8", 2", 2 5/16") for your trailer, and shank diameter (the…

view full answer...

Answer 5

There sure is! You'll need the Hopkins 48" 4-way Extension #HM47114 to allow the Brake Light #CR-007 to work in the Reese extension you have with your truck bed camper installed.

view full answer...

Answer 6

Thank you for all of the photos and information! From what I can see it looks like you have a #84 spindle but that inner bearing blew out so you should be able to remove that inner sleeve that looks like it's still on the spindle (next to where…

view full answer...

Answer 7

I do have a solution for you, however, the Patriot #BWRVK3270 is not compatible with your 2021 GMC 2500HD with the factory puck system due to the slider mechanism. There is currently no adapter or way to make this hitch work with your vehicle. You…

view full answer...

Answer 8

For a boat trailer, the best finish is going to be galvanized. The Kenda 5.70-8 Bias Trailer Tire with 8" White Wheel - 4 on 4 - Load Range C #AM30120 that you were looking at may work fine, but I don't recommend it for boat trailers since…

view full answer...

Answer 9

For your tire size of 275/70-17 the Konig tire chains part #KON94FR are an easier to install set that provide excellent traction and will last a long time as well. On a two wheel drive truck you can get by with a single set installed on your rear…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...