Replacement Rail Clamps for an Pace Edwards Switchblade Cover on a 2020 Toyota Tacoma

Question

Question:

I need replacement rail brackets for a pace edwards switchblade retractable tonneau cover for a 2020 toyota tacoma

asked by: Troy W

0

Expert Reply:

For your Pace Edwards Switchblade Retractable Hard Tonneau Cover # 311-SWTA10A38 you're just going to need the Replacement Rail Clamps for Pace Edwards Retractable Hard Tonneau Cover # PE84FR.

expert reply by: Bryce D

0

Answer 1

We do have the clamps you are wanting, but the Replacement Rail Clamps For Pace Edwards Retractable Hard Tonneau Cover #PE84FR includes the clamps and the mounting hardware. There is currently not a way to order the clamps without the mounting…

view full answer...

Answer 2

There are a few differences between the BAK Revolver X2 and X4s tonneau covers. The X4s is the newest cover available by BAK, so it includes a new matte black finish on all sides, whereas the X2 will be matte on the top, and then silver on the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to prevent the steering wheel in your 2017 Chevy Sonic from locking up when flat towing it behind your RV, you will just need to make sure to follow the steps in the vehicle's owner's manual, specifically the proper key position. I…

view full answer...

Answer 9

There are a few differences between the Demco Demco Stay-IN-Play DUO Supplemental Braking System w/ Wireless Coachlink Monitor #DM86VR and the Roadmaster InvisiBrake Supplemental Braking System #RM-8700. The biggest difference between the two is…

view full answer...

Answer 10

Hi Steve, thanks for the question, and we do indeed have the correct mounting panel for the Redarc Tow-Pro Liberty #RED24FR on your 2007 Toyota Tacoma. What you need is the following: - Mounting Panel for Redarc Tow-Pro Trailer Brake Controller…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Yes, it will but you may need a spacer. The reason I say may is most 3" lifts are not 3" in the rear. If your 2013 Toyota Tacoma has less than a 2" lift in the back then all you will need is the Air Lift LoadLifter 5000 Air Helper…

view full answer...