Replacement Polyurethane Bushing Kit For 1-3/4" Diameter Sway Bars

Question

Question:

How can I get a set of replacement 1 3/4sway bar bushings?

asked by: Wayne D

0

Expert Reply:

It sounds like you are needing the Roadmaster Polyurethane Bushing Kit # RM-4109-106. This includes bushings for a 1-3/4" factory sway bar.

expert reply by: Bud M

0

Answer 1

It sounds like you're looking for the Replacement Bushing for Roadmaster Front Anti-Sway Bar for Motor Homes - Qty 1 #RM-205393-00, which you'll need 8 of. For the bushings that fit around the bar you'll need the Roadmaster Polyurethane…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to where…

view full answer...

Answer 4

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 5

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 6

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Answer 7

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...

Answer 10

I found the online version of the install instructions for the Exact Center stabilizers like the #RM47MR. What's fun is that just when you think you have found the correct step to address your problem it tells you to continue to the next step.…

view full answer...

Answer 11

I recommend starting with the Roadmaster Rear Anti-Sway Bar, #RM-1139-147. This will reduce side-to-side movement for a noticeable improvement in your vehicle's stability and reduced body roll. For the front, I recommend the Timbren Front…

view full answer...

Answer 12

The Roadmaster #RM-1139-140 and #RM-1139-148 are both replacement anti-sway bars for a Ford F550 or F53 Class A motorhome chassis. Both bars are 1-3/4 inches in diameter. The #RM-1139-140 fits models with a GVWR of 22K-24K, and the #RM-1139-148 fits…

view full answer...