Which Bushings to Replace Bushings on Roadmaster 1-3/4 Inch Anti-Sway Bar

Question

Question:

I need 8 end bushings for the ends and 2 bar bushings. 1-3/4 bar RM1209-136. I am unable to find part numbers.

asked by: Theron G

0

Expert Reply:

It sounds like you're looking for the Replacement Bushing for Roadmaster Front Anti-Sway Bar for Motor Homes - Qty 1 # RM-205393-00, which you'll need 8 of.

For the bushings that fit around the bar you'll need the Roadmaster Polyurethane Bushing Kit for 1-3/4" Diameter, Factory Rear Anti-Sway Bar # RM-4109-106 for a complete set with mounting hardware.

expert reply by: Erik B

0

Answer 1

I checked with Roadmaster, and there are a couple of different bushings, depending on what you needed, for the Roadmaster Front Anti-Sway Bar and TruTrac Rod Kit #RM-1259-106. The correct replacements are the following: - Roadmaster Split Bushing…

view full answer...

Answer 2

Assuming that you're needing the steel U-clamp and replacement bushing for a Roadmaster #RM-1259-105 front anti-sway bar installed on your motorhome built on a 2003 Workhorse W22 Chassis, the replacement U-strap is part #RM-B141 and the…

view full answer...

Answer 3

When installing the Roadmaster Split Bushing for Anti-Sway Bar part #RM205222-10, I recommend using the LubriMatic Marine Trailer Wheel Bearing Grease part #L154FR. This is the same type of aqualube grease that comes with the kits from Roadamster.

view full answer...

Answer 4

It sounds like you are needing the Roadmaster Polyurethane Bushing Kit #RM-4109-106. This includes bushings for a 1-3/4" factory sway bar.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Roadmaster Exact Center Steering Stabilizer w/ Custom Brackets #RM47MR typically comes centered and you would only need to make adjustments after installation and testing to see if it continues to pull. If you adjusted it all the way out to…

view full answer...

Answer 8

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just…

view full answer...

Answer 9

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a…

view full answer...

Answer 10

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of…

view full answer...

Which Bushings to Replace Bushings on Roadmaster 1-3/4 Inch Anti-Sway Bar

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching