Width of Tandem Axle Teardrop Trailer Fenders for Boat Trailers

Question

Question:

It says the fenders are slanted on the back side. Mine are also for bass boat. What is the bottom width and top width?

asked by: Billy B

0

Expert Reply:

The Tandem Axle Teardrop Trailer Fenders for Boat Trailers - Steel - 14" Wheels # HP54VR measures 7-3/4" at the top and then 9" at the bottom (see attached).

Our video team member goes over this as well in the linked review video.

expert reply by: Jon G

0

Width of Tandem Axle Teardrop Trailer Fenders for Boat Trailers
(click to enlarge)

Answer 1

We only have the Tandem Axle Teardrop Trailer Fenders #HP94VR in this variation which is cold rolled steel. We do not have a galvanized version. This would be free of rust and clean when it shows up but you would want to paint it to prevent rust.

view full answer...

Answer 2

The #HP54VR fenders are 9 inches in width all along their length, as shown in the provided photo. All the tandem axle trailer fenders we offer for 14 inch wheels would be the same width. I've linked to an install video that you might find…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 10

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...