Recommended D-Ring Tie-Down Anchor For With An Endless Loop
Question:
I have the same size D-ring floor anchors in my toy hauler. They are stamped 2500 LBS. Problem with them is that the D-ring is not endless and anytime I have to anchor a load from the side slightly off center the D pulls apart at the break using just minimal pressure. See photos attached. Do you offer a similar anchor that has a solid endless D-ring that I could replace these with? A lower pound rating would be fine. Thanks.
asked by: Donald P
Expert Reply:
For a tie down D-Ring that doesn't have a weld to fail like your current tie-down you'd have to transition to a different design like the etrailer D-Ring Tie Down Anchor # RRING-Q6000. The options we have with the same design that you currently have unfortunately don't come with an endless loop so you'd have to switch to a different design. It has a maximum load (break strength) of 6,000lbs and safe working load limit (WLL) of 2,000lbs. I've attached a diagram of its dimensions below as well as a short video where Jake will walk you through the installation process.
(click to enlarge)
(click to enlarge)
Products Referenced in This Question
etrailer D-Ring Tie Down Anchor - Bolt On - 4-7/8" Wide - Square Mounting Holes - 2,000 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Tie-Down Cleats and Rings
- 2000 lbs
- D-Ring
- Recessed Mount
- etrailer
more information >
Product Page this Question was Asked From
Brophy D-Ring Tie Down Anchor - Bolt-On - 3-9/16" Wide - Recessed Mount - 400 lbs
- Tie Down Anchors
- Trailer Tie-Down Anchors
- Truck Tie-Down Anchors
- Tie-Down Cleats and Rings
- 400 lbs
- D-Ring
- Recessed Mount
- Brophy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Brophy Swiveling D-Ring Anchors w Backing Plates and Hardware - Bolt-On - 2,000 lbs - Qty 4
- Search Results: floor anchor
- Shop: Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor
- Shop: Brophy Swiveling D-Ring Tie Down Anchor - Bolt-On - 6-5/16" Wide - Recessed Mount - 2,000 lbs
- Search Results: tie~down anchors
- Shop: D-Ring Anchor w/ Backing Plate and Hardware - Bolt-On - 3-9/16" Wide - Recessed Mount - 400 lbs
- Shop: Backing Plate for RR06 Recessed Swivel D-Ring Tie Down
- Shop: Brophy D-Ring Tie Down Anchor w Backing Plate - Bolt-On - 1/2" Wide - Recessed - 1,600 lbs
- Shop: Brophy D-Ring Tie Down Anchor - Bolt On - 1/2" Diameter - 2,000 lbs
- Q&A: Replacement Tail Light for Utility Trailer With Command Electronics 003-5400
- Search Results: wheel hub caps
- Search Results: rr06
- Search Results: lug nut
- Search Results: strap hinge
- Search Results: recessed d ring
- Video: Polar Hardware Enclosed Trailer Parts - Doors - PLR2216 Review
- Video: Redline Enclosed Trailer Parts - Doors - L1930 Review
- Video: Optronics Trailer Lights - Clearance Lights - MCL48AB Review
- Video: Pollak 7-Way to RV Socket LED Circuit Tester Review
- Video: ComeUp Electric Winch CU881081 Review
- Q&A: Length and Diameter of Replacement Hitch Pin Clips
- Video: Review of Gen-Y Hitch Hitch Pins and Clips - 10 Pack of Hitch Pin Clips - GY69FR
- Video: Optronics Trailer Lights - Clearance Lights - STL75AMFB Review
- Shop: Trailer Wiring
- Q&A: Installation of Coupler Repair Kit # CP02-050
- Shop: Tire Chains
- Q&A: Recommended Hitch for a 2021 Toyota Venza that Does Not Affect the Parking Sensors
- Q&A: Does the Pipe Mount BDPG9810-00 and Trailer Jack TJDP-7000S-B Have Same Pipe Dimensions
- Q&A: Replacement Rod and Nut for a Bulldog 12,000 lb Trailer Jack
- Article: Most Popular Wheel Bearings
on Tie Down Anchors
