Replacement Hardware for Curt, Da'Lan, Draw-Tite, etrailer, Hidden Hitch or Reese Trailer Hitches

Question

Question:

Hello I have a 2007 Honda Odyessey. I already have a trailer hitch for the vehicle but the hardware to mount it to the vehicle is missing. Do you sell just the hardware? If not can you provide the bolt sizes I need for this installation? Thank you.

asked by: Mike G

0

Expert Reply:

Yes, we do sell just the hardware for Curt, Da'Lan, Draw-Tite, etrailer, Hidden Hitch or Reese trailer hitch receivers. You will want the Replacement Hardware Kit for Trailer Hitches item # RHK. This will give you all of the nuts, bolts, spacers, and even a fish wire tool if your hitch requires them for install. The bolts will be of the correct grade too so you won't have to worry about a parts failure.

You will need to know your hitches part number. When you go to the Replacement Hardware Kit for Trailer Hitches item # RHK page there is a box on the right hand side of the page that says Hitch Item Number.

Please feel free to email me directly with any additional questions.

expert reply by: Jerred H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 11

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 12

We do sell replacement hardware for all of the hitches we carry with the part #RHK but you might check down in the hitch tube to see if the hardware is taped up in there as that's sometimes where it's stored in shipping.

view full answer...