Can Brophy Hitch Extender # HE06 Work with Hollywood Racks RV Rider Bike Rack

Question

Question:

Does the Brophy hitch extender have enough receiver depth to accept the Hollywood RV Rider bike rack shank? Tried the Curt extender with no success. Pin holes did not align.

asked by: Scott M

0

Expert Reply:

Yes, the Brophy hitch extender part # HE06 that you referenced does have the needed depth to work with the Hollywood Racks RV Rider part # HLY64FR.

expert reply by: Jameson C

0

Answer 1

Yes, the Yakima BackSwing Swing Away Hitch Extender part #Y02483 can be used on the back of a toad vehicle therefore this is what I recommend you use.

view full answer...

Answer 2

The Swagman Quad 2+2 S64692 has a measurement of 17-1/4 inches from the center of the hitch pin hole to the closest wheel tray. The shank raises at the 10 inch point. To get your swing away, I recommend the Yakima BackSwing #Y02483 which is 14-1/2…

view full answer...

Answer 3

The Hollywood Racks RV Rider #HLY64FR is an excellent option for transporting your 2 M2S All Terrain Scout E-Bikes! It was designed to be used with a motorhome, has a weight capacity of 70 lbs per bike, and uses a clamping arm that can be moved…

view full answer...

Answer 4

Since you have a heavier e-bike at 74 lbs you'd need our e-bike rack with the highest weight rating of 80 lbs per bike with the Hollywood Racks RV Rider part #HLY64FR and then to allow it to pivot out and away from the vehicle you'd need the…

view full answer...

Answer 5

I have just what you need. I recommend the Yakima BackSwing #Y02483 which is rated for up to 250 lbs and will work well for your cargo carrier. It was created for bike racks, but you can use other accessories like a cargo carrier as long as you stay…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Yes, the Brass Tire Sensors for TireMinder TPMS #TM-2Brass would fit and work on the valve stems of your 2023 Jeep Wrangler.

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Can Brophy Hitch Extender # HE06 Work with Hollywood Racks RV Rider Bike Rack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching