Will CE Smith Single Axle Trailer Fenders Work With 13 Inch Wheels

Question

Question:

i have a cradle ride single axle boat trailer that i would like to put 13 inch wheels on it is 12 now will your fenders for 13 inch work

asked by: Kirke F

0

Expert Reply:

Yes, if you have 12" wheels now and want to move to 13" wheels you can use the CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 13" Wheels # CE19503-2.

The # CE19503-2 will work fine with your current 12" wheels and allow you to move to 13" wheels. To mount them use the Mounting Brackets # CE26098G-2.

expert reply by: Kyle S

0

Answer 1

While the part number you mentioned does not cross-reference to anything on our end, however I do still have a few options that may work for you. Typically fenders do not have custom mounting brackets so as long as your fenders are for single wheels…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

I went out to our warehouse to take a look at both the CE Smith Single Axle Trailer Fenders - 12" Grey #CE19502-2 and the larger 13" Black #CE19503-2. Both options represent the only color available from CE Smith in the respective sizes.…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...