Will B&W Continuum Weight Distribution System Work with Center Frame Piece on Trailer Tongue

Question

Question:

I want to purchase the bandW continuum, but my trailer has a center frame piece that goes to the hitch and is in the way. Are they coming out with one to fit trailers like mine?

asked by: Jeff L

0

Expert Reply:

The B&W Continuum Weight Distribution System part # BW78FR requires at least 24" of space on the frame directly behind the coupler and along the side a few inches back from there. This works with most trailers but for some it will not and, unfortunately, this sounds like the case for you (I included a picture of a trailer it will not fit for reference). However, you can either make modifications to the frame or choose a different system as there is not a workaround for this, nor is there one in the works. With that being said, I recommend the Equal-i-zer Weight Distribution System like part # EQ37100ET which is one of the best systems for the money and it's unmatched in sway control. If you need a different capacity, simply browse the list below.

Just as a side note, this will be the same as the 2-1/2" version # BW28FR as well as the 2" Underslung # BW53FR and 2-1/2" Underslung # BW88FR.

expert reply by: Conner L

0

Trailer With Center Frame Piece In A-Frame
(click to enlarge)

Answer 1

The chain lift brackets that come with the Curt MV Weight Distribution System #C17052 have a single 1/2" bolt that is used to secure the bracket to your trailer frame. The instructions call out to turn the bolt until it makes contact with your…

view full answer...

Answer 2

I attached a link to a page that has all of the 2,000 lb axle hub/drums we carry with a 5 on 4-1/2 inch bolt pattern. What you will need to do is pull the bearings out of your current hubs and select the numbers you have from the filters on the page…

view full answer...

Answer 3

Thank you for all of that info. Based on that you'd need a 3,500 lb trailer axle hub and drum with 5 on 4-1/2 inch wheel bolt pattern and matching brake assemblies. For that you'd want the #AKHD-545-35-K for the hub which comes with all…

view full answer...

Answer 4

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 5

To determine the tongue weight of your trailer when it is unloaded or loaded will require you to weigh it. For more info on that check out the link I attached. The tongue weight of a trailer isn't always listed. The best way to pick out a weight…

view full answer...

Answer 6

If you choose a hitch that is too light for your application it will not be effective. If you choose a hitch that is too heavy, you'll suffer a rigid ride and a bouncy trailer. Ideally you want a system that has a tongue weight capacity where…

view full answer...

Answer 7

A weight distribution hitch should be selected based on the fully loaded tongue weight of your setup. The best way to get your tongue weight is to use a scale like the #e99044. Tongue weight is typically 10-15% of your trailer weight so in this case…

view full answer...

Answer 8

When it comes to installing a weight distribution hitch on your Jayco Mini Trailer weighing right under 5,000 pounds I recommend The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 10,000 pounds GTW, 1,000 pounds TW #EQ37100ET. When…

view full answer...

Answer 9

I wish there was an easy solution I can recommend but Air Lift will void your warranty if you run lower than 5 psi in the bags and the compressor kit won't let you do that anyway. 5 psi SHOULDN'T make it unbearably stiff so I'd hate to…

view full answer...

Answer 10

If you have a 4-wheel drive and the fifth wheel frame brackets are installed on the outside of your 2015 F-350 frame rails, and the hole in the frame is open as the attached drawing shows. then the Air Lift suspension system that will work is part…

view full answer...

Answer 11

I spoke with my contact at Air Lift and he informed me that for your 2016 Ford F-250 with the factory camper package the Air Lift kit part #AL88396 would work and mounts in a way that matches what you sent in a picture of.

view full answer...

Answer 12

I would be happy to help! There is not a kit that includes Air Lift Air Helper Springs for the front and rear of your 2012 Ford F-250/350, but I would be happy to piece one together for you. For the rear the Air Lift LoadLifter 7500 XL Air Helper…

view full answer...

Will B&W Continuum Weight Distribution System Work with Center Frame Piece on Trailer Tongue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching