Is the A-Frame Trailer Coupler CA-5400-B a 50 Degree Coupler

Question

Question:

is your item Item # CA-5400-B set at 50 degrees for the trailer frame?

asked by: Walt S

0

Expert Reply:

Yes, the A-Frame Trailer Coupler part # CA-5400-B is a 50 degree coupler. It requires welding for installation and is designed for use with a 2-5/16" hitch ball.

expert reply by: Conner L

0

Answer 1

Some couplers can be adjusted so that the wedge will grab the trailer ball more tightly, but since the coupler you're using has no adjustment available, I'd first confirm that you are using the correct trailer ball size for your coupler. The…

view full answer...

Answer 2

To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow, and adding to that the weight of anything loaded behind…

view full answer...

Answer 3

Currently the only way to replace the coupler mechanism on the A-Frame Trailer Coupler #CA-5400-B is to replace the entire coupler. If you are going to do this you should look at changing to the Demco 50-Degree A-Frame Trailer Coupler #12660-97SP as…

view full answer...

Answer 4

To remove the 3" cap on your Valterra Sewer Drain like #T30A I recommend using the FloTool GRIPTECH 3-Position Adjustable Pliers #FT10627GT which can be adjusted between 2-3/4" and 4" to give you extra leverage in removing the cap. For…

view full answer...

Answer 5

Basically, one friction-style sway control can be used for trailers with up to 6,000-lb GTW. If your trailer's GTW is between 6,000 lbs and 10,000 lbs, you will need two sway-control units, one on each side of the trailer. You will also want to…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Is the A-Frame Trailer Coupler CA-5400-B a 50 Degree Coupler

Product Page this Question was Asked From

Continue Researching