Class III Trailer Hitch Receiver For 2022 Subaru Forester Wilderness

Question

Question:

I have a 2022 forester wilderness. I want a class 3 tow hitch. What do I buy from u guys. Tx

asked by: Wayne S

0

Expert Reply:

The correct Class III, 2 inch trailer hitch receiver for your 2022 Subaru Forester Wilderness is from Curt, and is the following part number:

- Curt Trailer Hitch Receiver # C13409

I have added a review from a customer who put the # C13409 on their Wilderness so you can see how well it fits. The only other thing you may need, if you plan on towing with the hitch, is a 4-flat wiring harness, the Vehicle Wiring Harness # C56040.

expert reply by: Kyle S

0

Customer Review of Curt Trailer Hitch Receiver C13409 on Subaru Forester Wilderness
(click to enlarge)

Answer 1

For your 2023 Subaru Forester, I recommend the etrailer Hitch item #e83ZR. This hitch is custom fit and bolts to your Subaru with included hardware. It is a class III hitch with a 2" receiver. I have linked an installation video below and…

view full answer...

Answer 2

Yes, the Curt T-Connector Vehicle Wiring Harness part #C56040 which is a fit for a 2020 Subaru Forester will come with a set of written installation instructions which I have also attached for you below as well. Furthermore, Curt harness has really…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...