Does Curt SecureLatch Pintle Hook with 2" Ball Have Max Tongue Weight

Question

Question:

What is the maximum tongue weight for this model CU37FR hitch?

asked by: Gerald

1

Helpful Expert Reply:

There is not a maximum tongue weight rating for the Curt SecureLatch Pintle Hook with 2" Ball # CU37FR.

That's actually true of ball mounts in general, as they are rated for towing capacity but not tongue weight. The towing capacity of the # CU37FR is 14,000 lbs or 10,000 lbs for the 2" ball for a standard coupler.

The only other thing you'll need with this is a hitch lock, the InfiniteRule Hitch Lock for 2" Hitches # 34061071-D.

expert reply by: Kyle S

1

Answer 1

The Curt SecureLatch Pintle Hook with 2" Ball #CU37FR (48407) requires a hitch ball with a 1-1/4" shank. The collar the shank fits into is 2" tall(see image). We do carry a 2" Replacement Ball #CU67FR as well as a 2-5/16"…

view full answer...

Answer 2

I have a solution for you, but the short answer is no, it does not. The Replacement Key for Andersen Hitch Receiver Locks and Locking Adjustment Pins #AM3499-2052 is code specific, so the key will only work on locks with a 2052 code. The codes for…

view full answer...

Answer 3

According to the folks at Curt, when the #CU37FR and #C48007 pintle hooks are designed and cast, they are not designed to withstand the force they'd be subjected to if they were inverted and used as standard ball mount. You'd be best served…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...