Where to Install Rhino Roof Racks Custom Fit Clamps # DK188 on a 2011 Ford Flex

Question

Question:

where do I position the roof racks?

asked by: Bob

0

Expert Reply:

According to the Rhino Rack installation instructions, for the # DK188 clamps, the front cross bar should be installed 25 cm, or 9-37/32 inches forward of the door seam between front and rear door. Then the rear crossbar will be installed 80 cm or 31-1/2 inches behind the front cross bar.

These installation measurements are confirmed for 2008 to 2014 Ford Flex that use the # DK188 Custom Clamps. I have included photo showing these dimensions for your reference, and have provided a link to these installation instructions for your reference.

expert reply by: Rachael H

0

click to enlarge

Answer 1

A good roof rack option is a Rhino Rack system. This has part numbers #RRVA150B-2, #RRRLKVA, and #DK188. This is a low-profile roof rack with aero bars and a t-track mounting system. This also uses a fit kit with hooks custom-fit for your 2014 Ford…

view full answer...

Answer 2

A great option for your 2019 Ford Flex is the Rhino-Rack Vortex Aero Crossbars #RRVA150B-2, with the Rhino-Rack 2500 Series Legs for Vortex Aero Crossbars #RRRLKVA, and the Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs #DK188. These…

view full answer...

Answer 3

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof…

view full answer...

Answer 4

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 8

For a wind fairing for 59 inch crossbars I recommend the Yakima WindShield Fairing for Roof Racks - 52" Long #Y05019.

view full answer...

Answer 9

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 10

Thanks for all the details! We definitely have a way to get a cargo basket and an awning installed on your 2024 Toyota Highlander, although the aftermarket roof rack systems will use a clamping system with your door jambs instead of mounting via…

view full answer...

Answer 11

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 12

I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…

view full answer...