Is There a 2" Trailer Hitch for a 2010 Subaru WRX

Question

Question:

Have a single exhaust 2010 WRX with an aftermarket exhaust. I know the answer it wont work has been provided, but Im trying to figure out WHY this wont work. Is it contact with a hanger? The exhaust itself? Something else? Im willing to make a modification to not have a hitch receiver showing at all times.

asked by: Chandler C

0

Expert Reply:

The only trailer hitch options we offer for a 2010 Subaru WRX with single exhaust are class I, 1-1/4" like the Draw-Tite Sportframe Trailer Hitch Receiver part # DT24959 which is what I recommend. However, hitches are only designed for factory exhaust so if you have aftermarket you may run into issues and need to make modifications. If you need the larger receiver then your only options are using an adapter, the Trailer Hitch Adapter part # e93YR.

I checked with EcoHitch but the EcoHitch Stealth Trailer Hitch Receiver part # 306-X7261 is not a fit for single exhaust models. I don't know why exactly as they do not provide this but if I had to guess I would say the muffle location is what makes the hitch incompatible.

expert reply by: Conner L

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 2

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Is There a 2" Trailer Hitch for a 2010 Subaru WRX

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching