Is There a Replacement Set Screw and Drive for Lippert Quick Drop Tongue Jack

Question

Question:

Do you sell the replacement drive nut and hex screw to fit the Lippert quick Jack on a wolf pup 17jg? My set screw broke and I’ve heard that the drive but cracks so would like to have a spare.

asked by: Allison F

0

Expert Reply:

If you're referring to the Lippert Quick Drop Tongue Jack part # LC733926, we don't have a replacement set screw or drive for this jack as they are not offered from Lippert as replacement parts. I would suggest you try your luck at a local hardware store as the only option we'd have for you is a new jack. In which case, I recommend switching to the Trailer Valet JXC Trailer Jack part # TV54FR which has the same drill powered option as the other jack but with a better finish and larger footpad.

expert reply by: Conner L

0

Answer 1

The closest equivalent manual jack, to the Lippert item #LC285318, would be the Buyers Products A-Frame Jack w/ Support Foot - 15" Travel - 5,000 lbs item #3370091265. This jack has the standard A-Frame jack 3" diamond pattern. I…

view full answer...

Answer 2

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 3

We have one sidewind A-frame jack with a 2 inch outer diameter tube, part #DL22530. This is a 1,000 pound jack from Dutton-Lainson that has 15 inches of travel. I've linked a video of the jack for you as well.

view full answer...

Answer 4

Yes, the Stromberg Carlson Electric Trailer Jack #JET-5000 is an excellent option for you. It is capable of lifting a trailer up to 18" with up to 5,000 lbs. of tounge weight. In comparison to the Atwood Premier Performance Series Power Jack…

view full answer...

Answer 5

If you take a look at the diagram I've provided for the Replacement Power Switch for RAM Electric Trailer Jack with Footplate #EJ-3520-PSW which goes to the Electric Jack w/ Footplate #EJ-3520-WBX, you'll be able to see how both of…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 10

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 11

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 12

We don't currently have any customer submitted photos for the Brophy Heavy Duty Cable Camper Jacks #CX74, but we do for the lower capacity #CJ74, which uses the same lift brackets. From the edge of the tube to the lift bracket is approximately…

view full answer...