How To Fill The Yakima RoadShower Portable Solar Shower # Y79VR with Water

Question

Question:

How do you put water in to the unit? Does it require a pressurized water source?

asked by: TIM D

0

Expert Reply:

There are 2 ways to fill the Yakima RoadShower Portable Solar Shower # Y79VR with water. If you have a pressurized water source you can use the included quick connect to attach a hose allowing you to fill the tank from the same port you attach the water sprayer hose. You can also remove the check valve/cap from the top the unit to be able to fill the tank. This is the preferred route to use if you do not have a pressurized water source. As it is on top of the tank it may be difficult to access depending on your vehicle and other accessories.

expert reply by: Bud M

0

Answer 1

The Fastway Flip Automatic Fold-Up Jack Foot #FA88-00-4500 when folded in the stowed position will reduce ground clearance from the hole in the jack tube by approximately 3-inches. This is shown in the photo I prepared for you.

view full answer...

Answer 2

All-around the Stromberg Carlson Electric Trailer Jack #JET-5000NG is nicer than the #JET-5000. The bearings in the part #JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is…

view full answer...

Answer 3

On a lot of powered a-frame jacks if you extend or retract them too far you end up warping the nut and screw that allows the jack to travel up and down. When this happens there isn't a way to fix it as the jack is permanently damaged. It's…

view full answer...

Answer 4

I have not seen any additional add on parts for the Fastway Flip Automatic Fold-Up Jack Foot #FA88-00-4500 that will do what you are looking for. And it can be used on a pop up that is using a 2-1/4" tongue jack. I recommend the Roadmaster Quick…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 10

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

How To Fill The Yakima RoadShower Portable Solar Shower # Y79VR with Water

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching