Solution for Trailer Jack that Was Retracted too Far and was Damaged

Question

Question:

Evidently Retracted too far! Now, though running, wont budge up or down? What do I do?

asked by: Bruce H

0

Expert Reply:

On a lot of powered a-frame jacks if you extend or retract them too far you end up warping the nut and screw that allows the jack to travel up and down. When this happens there isn't a way to fix it as the jack is permanently damaged. It's time for a new jack.

As a replacement, I recommend the Stromberg Carlson Electric Trailer Jack, # JET-5000.

It has a lifting capacity of 5,000 lbs which would be more than you'd need but will ensure that the jack will operate quickly and last a long time.

expert reply by: Jameson C

0

Answer 1

All-around the Stromberg Carlson Electric Trailer Jack #JET-5000NG is nicer than the #JET-5000. The bearings in the part #JET-5000NG allow it to raise and lower much smoother and quicker, the size of the head is a bit smaller and the lighting is…

view full answer...

Answer 2

To replace your lost storage compartment keys you'll just need to know the brand and lock code to find the correct replacement key. Each lock typically has a 3-digit code representing what the lock code. For example, the Replacement Key for…

view full answer...

Answer 3

Any time a trailer has turn signals that work but not the brake lights it can be an interesting situation. This is because the brake lights and turn signals on trailer tail lights are on the same circuit. In this situation it is almost always a bad…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 12

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...