Recommended Ramps to Reduce Approach Angle to Load BMW Z3 in Toy Hauler
Question:
I have a 5th wheel toy hauler that I want to load a BMW Z3. I need to lessen the incline because the bumper scrapes the door/ ramp. Could these be used to extend the loading ramp so that the angle is decreased? My thought is to set the ramps at the mid point of the 8ft door/ ramp. This will then extend the 84inch ramps 3ft past the end. FYI, floor height is 3ft. Thank you.
asked by: Gary K
Expert Reply:
I do have a solution, but the # 325-GH-R84 are not designed to work this way. Since they are designed to hook over the back edge of a trailer, you would drop off of the end where the hooks are onto the ramp of your 5th wheel. It would not be a smooth transition and depending on your clearance you might cause damage. They may also pop up into your Z3 when you drive off the end of the ramps.
Instead, I recommend the Race Ramps Trailer Loading Assist Ramps # RR-TR-5. These have cutouts so you can lay your toy hauler door on the ramps. They are also significantly lighter and easier to handle with their foam construction at 10 lbs per ramp. The ramps will reduce the angle of approach to 4.3 degrees so you can load your Z3 without the bumper scraping.
Products Referenced in This Question
Race Ramps Trailer Loading Assist Ramps - 5" Lift - 67" Long - Qty 2
- Car Ramps
- Loading Ramps
- Enclosed Trailer
- 14 Inch Wide
- 5 Inch Lift
- 67 Inch Long
- Car Hauler Ramps
- 3000 lbs
- Race Ramps
more information >
Product Page this Question was Asked From
Gen-Y Hitch Aluminum Loading Ramp Set - 7' Long x 14" Wide - 6,000 lbs
- Car Ramps
- Loading Ramps
- Open Trailer
- 14 Inch Wide
- 84 Inch Long
- Car Hauler Ramps
- 6000 lbs
- Gen-Y Hitch
more information >
Continue Researching
- Video: Gen-Y Hitch Aluminum Loading Ramps Review
- Q&A: Loading Ramp Recommendation for a 3000-Pound Tractor with 20-Inch Deck Height on Trailer
- Q&A: How Wide is Gen-Y Ramp 325-GH-R84 Hook
- Q&A: What Is the Minimum Deck Height of the Gen-Y Hitch Aluminum Loading Ramp Set
- Q&A: Maximum Amount of Weight That Can Be Applied to 288-07489 Stallion Loading Ramps
- Shop: Aluminum Car Hauler Ramp Set - 72" x 14-1/2" - 6,000 lbs - Qty 2
- Shop: Race Ramps Trailer Loading Assist Ramps - 5" Lift - 67" Long - Qty 2
- Shop: Gen-Y Hitch Aluminum Loading Ramp Set - 12' Long x 15" Wide - 8,000 lbs
- Shop: Gen-Y Hitch Aluminum Loading Ramp Set - 7' Long x 14" Wide - 6,000 lbs
- Shop: Gen-Y Hitch Aluminum Loading Ramp Set - 6' Long x 14" Wide - 6,000 lbs
- Shop: Loading Ramp Set - Aluminum - 65" Long x 20-1/2" Wide - 3,000 lbs - Qty 2
- Shop: Trailer Hitch
- Search Results: trailer brake controller
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Q&A: Best Way to Prevent Sagging Suspension When Towing a Trailer
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer jack
- Article: Trailer Tire Sizing
- Video: etrailer Horizontal E-Track Review
- Shop: Suspension Enhancement
- Search Results: e~track
- Video: Stallion Aluminum Car Hauler Ramp Set Review
- Shop: Roof Rack
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Fifth Wheel Hitch