Recommended Replacement Rail Pins and Clips for Curt 5th Wheel Trailer Hitches

Question

Question:

Curt Q20 4 replacement pins Hitch to rail. Misplaced originals.

asked by: Don N

0

Expert Reply:

To replace the pins that hold your 5th wheel hitch to your trucks industry standard rails you will need the Replacement Rail Pins and Clips for Curt 5th Wheel Trailer Hitches item # C16902. These pins and clips are compatible with your Curt Q20 Hitch item # C16536.

expert reply by: Jerred H

0

Answer 1

There are two Curt 5th wheel service kits. The Curt #16125-SK3 kit is designed specifically for the Curt #C16125 hitch. The Curt #C45UR kit is for most other Q-series hitches. Unfortunately, Curt does not sell the grommets individually.

view full answer...

Answer 2

There are several parts on the Curt Q20 5th Wheel Trailer Hitch part #C16130 that need greased regularly; one zerk on each side of the head, one zerk in the center of the jaw, and the cam on the locking jaw mechanism. I have attached a photo that…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Answer 9

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Recommended Replacement Rail Pins and Clips for Curt 5th Wheel Trailer Hitches

Products Referenced in This Question

Continue Researching