Replacement Refrigerator Vent Latches For RV

Question

Question:

I am looking for the black square clips that hold the fridge vent on the side of my motor home they are black and about 1/4 square and you turn the slotted part of the clip to release the vent cover. do you carry these?

asked by: Lawrence R

0

Expert Reply:

I believe we do have what you are needing with replacement refrigerator vent latches. We offer a couple options, depending on the thickness of your wall.

- Up to 3/16" Thick: Refrigerator Vent Latches - Thick Wall # 372245

- Up to 1/16" Thick: Refrigerator Vent Latches - Thin Wall # 372235

expert reply by: Kyle S

0

Answer 1

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...

Answer 2

The Dometic RV Water Heater part #DMC74FR would fit really well in place of the Atwood G6A-7 that you mentioned having. This and what you have now are both 6 gallon water heaters of a very similar design to the fit would be very easy.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 11

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 12

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...