Weight Rating of Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System

Question

Question:

Would love to know the suggested Load rating for this Pad.

asked by: Andreas R

0

Expert Reply:

The Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System # LC324269 doesn't have a specified weight rating. Since this is a direct replacement for a hydraulic jack that does have a weight rating, like the 8K Lippert Level Up Hydraulic Jack # LC26FR, you just need to stay within the weight rating of that jack and you're good to go.

expert reply by: Jon G

0

Answer 1

Yes, you'd need to hold the inner jack leg while you remove the bolt from the bottom when replacing the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System part #LC324269. In order to hold the inner jack leg, I recommend…

view full answer...

Answer 2

You'll have to hold the leg of your jack still so that you can unscrew the bottom of the foot pad to replace it. If you have a large set of channel locks you could do this pretty easily with them. The trick will be hold it tight enough to keep it…

view full answer...

Answer 3

The replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System - Qty 1 #LC324269 needs to be torqued to 132 ft-lb and Lippert recommends using some Loctite Threadlocker 262 - High Strength - Up to 3/4" Nuts/Bolts - 0.20-Fl-Oz Tube…

view full answer...

Answer 4

The exact replacement foot plate for the Level Up system you have is not available as a replacement. But you could use #LC314667. The issue is that it uses a smaller bolt than the Level Up foot. So you would have to use a 1/2 inch bolt that will…

view full answer...

Answer 5

Thanks for the picture! I took a look at what we got for your 2018 Thor Palazzo Motorhome, and it appears you need the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269. This replacement will replace the foot pad for…

view full answer...

Answer 6

The Replacement Foot Pad #LC324269 that you referenced uses (and includes) a threaded 7/16" bolt for mounting. The mounting hole itself is just about 1/2" in diameter.

view full answer...

Answer 7

The SnapPad Prime Jack Pads #SP84FR4 are specifically designed to fit the Power Gear Leveling Systems w/ 10" Round Concave Jack Feet on your 2014 Fleetwood Bounder 34B. The Pads #SC99MR Stromberg told you to use will not fit on your Bounder as…

view full answer...

Answer 8

You are correct, the Replacement Footpad Kit #LC86UD is mounted with the bolt, flat washer, o-ring, footpad and finally the 2nd o-ring before threading into the base of the hydraulic jack.

view full answer...

Answer 9

For a 9 inch diameter jack foot pad I would go with the SnapPad part #SP54FR4 over the Stromberg part #SC99MR since the SnapPad will be a little bit larger in diameter which distributes the weight a little better.

view full answer...

Answer 10

If your 2021 Jayco Greyhawk Prestige has hydraulic Lippert Ground Control leveling system then yes the replacement feet part #LC324269 would be correct. I attached a picture of what the jack leg should look like.

view full answer...

Answer 11

Josh, the bolt for the Replacement Foot Pad for Lippert Hydraulic Ground Control Leveling System #LC324269 is 7/16" x 1/2" and needs to be torqued to 132 ft.-lbs.

view full answer...

Answer 12

I went ahead and pulled this Replacement I-Beam Jack Bracket #LC349975 from our warehouse to measure. I have attached the dimensions below. Hope this Helps.

view full answer...