Recommended 16" Long LED Vertical Tail Light

Question

Question:

Looking for a replacement led light. I can send you an image 16” long vertical trailer tail lamp

asked by: Jeremy K

1

Helpful Expert Reply:

We have a couple of options for vertical trailer tail lights that are 16". I have listed them below. These are our only options for 16" long LED tail lights.

16" x 1-5/16" x 11/16" - Optronics ThinLine LED Trailer Tail LIght - Stop, Turn, Tail - Submersible item # STL87RCB

16" x 1-5/16" x 11/16" - Optronics ThinLine LED Trailer Tail LIght - Stop, Turn, Tail - Submersible item # STL87RCPG

expert reply by: Jerred H

1

Answer 1

I may have a few parts that you can piece together to install tail lights on the Curt Cargo Carrier, #C18100, but Curt does not offer a tail light kit that will fit this carrier. If you are interested in the slim LED lights, you could install two of…

view full answer...

Answer 2

The only difference between the Optronics ThinLine LED Trailer Tail Light part #STL87RCB and part #STL87RCPG is that the latter has bullet style (removable) connectors and the former has bare wire ends.

view full answer...

Answer 3

This particular lamp is meant to be used in pairs, one on each side of the rear of the trailer. The red wire on the drivers side lamp is meant to connect to the yellow wire from the trailer connector, and on the passenger side lamp the red wire…

view full answer...

Answer 4

The difference between the Optronics LED stop/turn/tail light #STL69RRXB and the Optronics LED stop/turn/tail light #STL69RB is #STL69RRXB will have an integrated red reflector to fulfill the rear reflex requirement. If you choose to go with…

view full answer...

Answer 5

We don't carry lights with those colors, so you will need to test them based on function. Normally black and red are power and white is ground like you see in the #STL69RB. I would try the yellow as ground. Red is most likely the turn signal and…

view full answer...

Answer 6

The brake output circuit of your vehicle/trailer wiring wouldn't be an ideal circuit to power the third brake light of a trailer unless you wanted to modify the circuit on your tow vehicle. You would have to run a brake light circuit straight to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It's a wire color difference but not a function difference on the pins of the 7-way. The difference comes from the fact that the two different styles are representative of two different areas that uses trailers. Traditional is usually seen on…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Recommended 16" Long LED Vertical Tail Light

Product Page this Question was Asked From

Continue Researching