Differences Between the Optronics LED Stop/Turn/Tail Light Part STL69RRXB and Part STL69RB

Question

Question:

What is the difference between the STL69RRXB and the STL69RB?

asked by: Doug H

0

Expert Reply:

The difference between the Optronics LED stop/turn/tail light # STL69RRXB and the Optronics LED stop/turn/tail light # STL69RB is # STL69RRXB will have an integrated red reflector to fulfill the rear reflex requirement. If you choose to go with # STL69RB, then you will need to add 2 red reflectors to the back of your trailer to meet federal lighting requirements.

I recommend going with the # STL69RRXB because it's not much more in cost and you will not need any additional parts.

I included a couple video reviews for you too.

expert reply by: Chris B

0

Answer 1

The GloLight Thinline LED Stop/Turn/Tail Trailer Light #STL179RB is sold individually.

view full answer...

Answer 2

The GloLight Thinline LED Trailer Tail Light #STL179RB that you referenced does not have a base to mount to as it was designed to mount directly to a trailer surface.

view full answer...

Answer 3

To install the Optronics LED Trailer Lights, part #STL22RB, you will need to use the Straight 3-Wire Pigtail, part #A45PB. The Red wire of #A45PB will carry the turn signal function, the Black wire is for running lights, and White is ground. If you…

view full answer...

Answer 4

We don't carry lights with those colors, so you will need to test them based on function. Normally black and red are power and white is ground like you see in the #STL69RB. I would try the yellow as ground. Red is most likely the turn signal…

view full answer...

Answer 5

The Thinline LED Trailer Tail Light w/ Reflector - Stop, Tail, Turn - Submersible - 11 Diodes - Red Lens #STL69RRXB and The Thinline LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 9 Diodes - Red Lens #STL59RB come in quantity 1. I…

view full answer...

Answer 6

The Optronics Sealed Thin Line LED Stop/Turn/Tail Light #STL69RRXB that you referenced is a surface-mount (not a flush-mount) 3-wire fixture. This can be installed along with other standard incandescent lighting without any sort of adapter. The…

view full answer...

Answer 7

I'll compare some of the most different aspects of these 3 lights you referred to: The Thinline LED Trailer Tail Light - Stop, Tail, Turn #STL59RB has a clear lens with red LEDs. It is submergible and measures 12-5/8 long x 1 tall x 1/2…

view full answer...

Answer 8

If you're speaking of the grommet mounted 3 function taillight, part #ST70RB, the lamp would use the #A45PB straight or the #A47PB right angle pigtail. The red wire is for the turn signal/brake, the black is for running lamps and the white…

view full answer...

Answer 9

The brake output circuit of your vehicle/trailer wiring wouldn't be an ideal circuit to power the third brake light of a trailer unless you wanted to modify the circuit on your tow vehicle. You would have to run a brake light circuit straight…

view full answer...

Answer 10

We have a couple of options for vertical trailer tail lights that are 16". I have listed them below. These are our only options for 16" long LED tail lights. 16" x 1-5/16" x 11/16" - Optronics ThinLine LED…

view full answer...

Answer 11

I may have a few parts that you can piece together to install tail lights on the Curt Cargo Carrier, #C18100, but Curt does not offer a tail light kit that will fit this carrier. If you are interested in the slim LED lights, you could install two…

view full answer...

Answer 12

This particular lamp is meant to be used in pairs, one on each side of the rear of the trailer. The red wire on the drivers side lamp is meant to connect to the yellow wire from the trailer connector, and on the passenger side lamp the red wire…

view full answer...