Recommended 4-Way Wiring Harness for a 2023 Honda Ridgeline

Question

Question:

I have a 2023 Honda Ridgeline and I need a wiring harness for my trailer.

asked by: Everett

0

Expert Reply:

We have a wiring harness for a 2023 Honda Ridgeline depending on what kind of wiring your trailer has. Both harness plug into your factory wiring behind your rear bumper. These harnesses also include the necessary fuses to activate the towing functions on your vehicle. Honda leaves these out when they manufacture the Ridgeline.

For a 4-Way Harness that controls your trailer's lighting functions you will need the Curt Wiring Harness with 4-Pole Flat Trailer Connector item # C56365.

I have linked a screenshot below that will show you what the connector you will plug into looks like.

expert reply by: Jerred H

0

Ridgeline Wiring Harness Instructions
(click to enlarge)

Answer 1

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 2

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 3

While we don't have a video I can hopefully explain how to remove the cap of the wiring on your 2017 Honda Ridgeline to install the trailer wiring #118288. Remove the connector from the cross-member using a pry tool like #ALL648544. Remove…

view full answer...

Answer 4

The easiest solution would be to use the Tekonsha kit part #118384 which would plug inline with the 7-way you have now and give you a 4-way that when not in use could be totally hidden.

view full answer...

Answer 5

Thanks for the picture! I just spoke with my rep at Yakima and got some specifications and dimensions off of the Yakima BigCatch Kayak Carrier item #Y04091 you referenced. It is 9-1/4" x 6-1/2" x 5-1/2" and has a weight capacity of 150…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C29VV will not interfere with the kick sensor function on your 2024 Lexus RX 350h. To get it to work however, you'll have to kick to either side of the receiver instead of swiping your foot under the bumper for…

view full answer...

Answer 7

You did quite a bit of troubleshooting and homework on this so I commend you for that! Since it's not the relays, the fuses, or the trailer wiring that basically leaves the converter box of the wiring kit. Which you can test that with a circuit…

view full answer...

Answer 8

The Adapter Module for BrakeRite Electric Over Hydraulic Actuator #DX35FR was designed for use on the trailer side of the wiring. If you had this installed on the truck wiring the integrated controller would think a trailer is connected all the…

view full answer...

Answer 9

It sounds like you were needing the Adapter #DX35FR but accidentally ordered the adapter with the plug, part #T4845900, is that correct? If so, no worries. You can indeed cut the plug off the adapter and hardwire it as shown in the diagram I…

view full answer...

Answer 10

The Mopar Recreational Flat Tow Wiring Kit part 68321424AB is required on select Jeep Cherokee's in order to activate the electronic power steering (EPS) system while the vehicle is in tow mode. This part must be obtained from the dealer but…

view full answer...

Answer 11

We have everything you would need to flat tow your 2015 Jeep Cherokee Trail Hawk behind your motorhome. First you will need a base plate kit, which for that I would recommend the Roadmaster Base Plate kit part #RM-521446-4. In addition to the base…

view full answer...

Answer 12

Do you know who manufactured your existing bed rails? The Curt E5 16K Fifth Wheel Hitch you referenced, part #C16115 are compatible with universal rails manufactured by Reese, Curt and Valley. A universal rail will have three mounting slots on each…

view full answer...