Overall Length When Retracted of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels

Question

Question:

my trailer has a tongue that is only 23inch in length. I want to know what is the overall length of the Ark Extreme Off-Road Swing-Up Trailer Jack 350d is fully retracted

asked by: Jemail M

0

Expert Reply:

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, # ORJW350D has an overall length of 18".

expert reply by: Michael R

0

Extreme Off-Road Swing-Up Trailer Jack with Dual Wheels
(click to enlarge)

Answer 1

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 2

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 3

From the center of the mounting bracket (Pivot point) to the bottom of the wheels of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 7" Lift - 770 lbs - Zinc #ORJW350D is 9-1/2" with the jack full retracted, and is…

view full answer...

Answer 4

Hey Rich, that is a really good question. The short answer is, no, you do not need to go relocate your jack. According to the manufacturer, mounting the jack on the middle rail allows it to more evenly distribute the weight of the trailer, making it…

view full answer...

Answer 5

The Extreme Off-Road Swing-Up Trailer Jack part #ORJW350D would be the best option for an InTech Flyer Pursue Travel Trailer. The weight capacity of said jack is more in-line with the tongue weight of the trailer.

view full answer...

Answer 6

From the ground to the middle of the mounting bracket for the Extreme Off-Road Swing-Up Jack w/ Dual Wheels #ORJW500D measures 710mm (27.95") when you have it set at the highest setting. This jack gives us the ability to extend the leg using the…

view full answer...

Answer 7

The Ark Extreme Off-Road Swing-Up Jack #ORJW350D fits a wide variety of trailers. The mounting bracket will measure 7-1/2" tall x 5-1/2" wide. The vertical holes are 3/4" apart and the horizontal holes are 1" apart. This makes it…

view full answer...

Answer 8

Yes, in order to set your trailer up for use with shore power you will first need an AC distribution panel. For this, I recommend a Progressive Dynamics Series AC Distribution Panel. In order to bring power into the panel you will also need a power…

view full answer...

Answer 9

We have the Dexstar Steel Spoke Trailer Wheel - 15" x 5" Rim - 5 on 4-1/2 - White Powder Coat, #AM20422. This is the Dexstar 5" 017-143-1X wheel. For a tire with a 2150 lb. load rating that fits this wheel, I suggest the Karrier…

view full answer...

Answer 10

I recommend the Master Lock Hitch Receiver and Coupler Latch Lock Set #2848DAT. These are made by Master Lock and has 6 locking positions that fits a 5/8" latch width, which is the size of most standard couplers, a 1" latch width, which is…

view full answer...

Answer 11

I contacted Stinger Trailers and was able to verify that the Bearing Kit #BK2-100 you referenced is exactly what you need to replace the bearings and seal for the hubs on your folding motorcycle trailer. The Sure-Lube system on the trailer features a…

view full answer...

Answer 12

I recommend using the Xtreme Off-Road Swing-Up Trailer Jack #ORJW350D as we do not have a jack which will fit the same weld on bracket you have on your boat trailer. This jack can be bolted onto your frame and will allow you to have more…

view full answer...

Overall Length When Retracted of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching