Recommended B&W Companion Hitch/Base that Fits the Reese Elite 5th Wheel System

Question

Question:

Will the BandW Companion OEM 5th Wheel Hitch for Chevy/GMC Towing Prep Package fit the Reese Elite Series Under-Bed Gooseneck Complete Hitch, Item # RP30158-68?

asked by: Diego G

1

Helpful Expert Reply:

I have a solution for you but the Reese Elite Series Under-Bed Gooseneck Complete Hitch, Item # RP30158-68 uses the same pattern as the Ford factory puck system. The correct B&W hitch will be the B&W Companion item # BWRVK3300 for a fixed hitch and a long bed or item # BWRVK3370 for a slider hitch if you have a short bed and need the extra turning clearance.

If you already have the head and just need to replace the base you will want the item # BWRVB3300 for the fixed base and item # BWRVB3370 for the slider base.

The Chevy/GMC OEM Puck pattern is different so nothing that fits a Chevy or Ram will work with the Reese Elite.

expert reply by: Jerred H

1

Answer 1

Yes, there is an option to add an aftermarket under bed puck system to your 2018 Chevy Silverado 2500. It is the Elite Series Under-Bed Gooseneck Complete Hitch item #RP30158-68. This under bed system has a towing capacity of 25,000 lbs. I have…

view full answer...

Answer 2

The B and W Companion OEM Ford Rail Kit part #BWRVK3370 that you referenced weighs 262 lbs.

view full answer...

Answer 3

Yes. The Reese Under-bed Rail and Installation Kit for Reese Elite Series Hitches #RP30868 is a confirmed fit on your 2018 GMC Sierra 2500 and will install using existing holes in the frame; any drilling that would be required during installation…

view full answer...

Answer 4

The Reese Under-Bed Rail and Installation Kit for Reese Elite Series 5th Wheel Trailer Hitches #RP30868 are not the same puck configuration as the Factory GM puck system. However, they are in the same configuration as the Ford Factory puck System, so…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

There is a gooseneck hitch that will work with the puck system of your 2012 Chevy 3500 and even allows the use of a fifth-wheel hitch. The Elite Series Under-Bed Gooseneck Complete Hitch #RP30158-68 was made specifically for GM trucks, uses a pop-in…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 10

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...