Distance Between Mounting Holes on Curt 14001 for 1999 Dodge Ram

Question

Question:

Distance between each mounting hole?

asked by: Joe

0

Expert Reply:

The distance from the front hole to the middle on the # 14001 is 5.2". From the middle to the rear hole is 4.04" and from the front hole to the rear hole is 9.2". The distance across for each set of mounting holes is 36".

expert reply by: Robin H

0

Curt 14001 Dimensions.
(click to enlarge)

Answer 1

The Curt Class IV Receiver Hitch #14001 referenced in your question is indeed confirmed to fit your 1993 Ford F-150 Pickup if it has a standard or step bumper. I spoke with my contact at Curt and he stated that the 1993 Ford F-150 did not have a…

view full answer...

Answer 2

The 7-Pole and 4-Pole Trailer Connector Sockets w/ Mounting Bracket and Wiring #HM40975-11998 is a hard wire application, as you can see in the linked installation video we made of this being put on a 2008 Ford F-250. If you only need to connect the…

view full answer...

Answer 3

The issue with hitch extenders is that they end up cutting the capacity of the hitch they are installed in by 50 percent due to the extra length and movement in the hitch. So with that in mind there isn't a hitch extender we can offer that will…

view full answer...

Answer 4

I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4…

view full answer...

Answer 5

I would be happy to help. The Curt Trailer Hitch Receiver #C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes. The Curt…

view full answer...

Answer 6

The overall length of the side plate that attaches to the frame on the TorkLift SuperHitch Original Trailer Hitch Receiver #TLF1000 referenced in your question is 22-1/2 inches. The trailer hitch has 6 holes on each side (12 total) and each hole is…

view full answer...

Answer 7

Curt Class V hitch #C15300 is a confirmed fit on your 1987 Ford F-150. To help you determine if it will be compatible with your skid plate I went to our warehouse and took a measurement of the hitch to find out the distance from the mounting brackets…

view full answer...

Answer 8

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 9

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 10

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 11

The Curt Trailer Hitch Receiver #C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes.

view full answer...

Answer 12

I spoke with my contact at Curt to obtain the mounting bolt hole locations for the Trailer Hitch Receiver, #C15300 on a 1993 Ford F-150. I have attached a picture to illustrate these measurements. As for repositioning the spare tire, you may need to…

view full answer...