Mounting Hole Dimensions of Curt Hitch # C15511

Question

Question:

Do you have bolt pattern measurements of mounting brackets.

asked by: Tom

0

Expert Reply:

The Curt Trailer Hitch Receiver # C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes.

expert reply by: Jameson C

0

Bolt Hole Dimensions of C15511 Hitch
(click to enlarge)

Answer 1

I was able to obtain from Curt a chart showing key dimensions for their 3-Piece Trailer Hitch #C15511 (and other hitch models) that I linked for you. This shows that for hitch #C15511 the overall front-to-back length is just under 24-inches. The…

view full answer...

Answer 2

We do carry the #84 spindle #TRU77FR which is designed to accept a 3" axle beam. The spindle itself has an overall length of 6-1/8". This is the only #84 spindle we have for a 3" tube. All of the others would be a #42 spindle like the…

view full answer...

Answer 3

To answer your first question, technically you can put truck wheels on your trailer, there are just a few things you will need to look out for. First, automotive grade wheels tend to have more of an offset than trailer wheels, meaning the center of…

view full answer...

Answer 4

From where the B and W hitch part #BWHDRH25198 attaches to the frame of a truck down to the top of the hitch opening measures 7-3/8 inches.

view full answer...

Answer 5

Yes, the #84 E-Z Lube Spindle w/ Brake Flange #TRU77FR will fit the 2" schedule 40 pipe.

view full answer...

Answer 6

I have attached a photo of the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25198 you asked about. I have noted the mounting holes on the photo you can check out. The distance center-to-center from the front mounting hole to the second is…

view full answer...

Answer 7

I checked with Trudyde, and I was able to find out that the bar stock material used to make the spindle #TRU77FR is hot rolled SAE 1045 steel which is a medium carbon common steel grade.

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

It looks like you have a 1976 Chevrolet C/K Series Pickup and need a trailer hitch with drop receiver to clear something such as a deep drop bumper. If that is the case then the Curt 3-Piece Trailer Hitch Receiver part #C15511 might be a good option…

view full answer...

Answer 10

Outstanding photos thank you so much for sending them, and based on that we do have a hitch that can fit your 1965 Ford F-250 with a custom bumper. Since the frame is clear from any interference with the bumper, all you need to do is measure from the…

view full answer...

Answer 11

The TruRyde #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles item #TRU77FR has a 3" inner diameter. The E-Z Lube spindle welds onto your 3,500-lb trailer axle it works with L68149 inner bearing and L44649 outer bearing. The Stub…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Mounting Hole Dimensions of Curt Hitch # C15511

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching