Does Gas Tank of 1994 Ford Bronco to Install Curt Hitch

Question

Question:

Does the gas tank need to be lowered or removed for a 1994 Ford Bronco installation? I assume holes need to be drilled as well ? Is there a video for this? Thanks!

asked by: Martin C

0

Expert Reply:

The gas tank of your 1994 Ford Bronco does not need to get removed to install the Curt hitch part # C15300 that you referenced. You will need to drill to install the hitch as well.

expert reply by: Jameson C

0

Answer 1

I went out to the warehouse to measure the Curt Trailer Hitch Receiver XD, Class V #C15300 and found that the measurement from the top of the mounting bracket to the top of the hitch cross tube/receiver measured 6-1/4 inches. From the bottom of the…

view full answer...

Answer 2

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 3

Since your 2008 Ford F-350 is a Stake Bed Truck you will need to look at the trailer hitches that fit an F-350 Cab and Chassis. I have linked our selection for you to filter through. The most popular choice is the B&W Heavy-Duty Trailer Hitch…

view full answer...

Answer 4

I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4…

view full answer...

Answer 5

I would be happy to help you. I have linked some diagrams with every dimension you will need. The Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2" item #C15300 is confirmed to fit a 1979 Ford Bronco.

view full answer...

Answer 6

The B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 that will fit your 1986 Chevy K20 will measure 5.438" from the top of the frame brackets to the top of the receiver. If this is looking like it will not be enough to clear the bottom of…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Does Gas Tank of 1994 Ford Bronco to Install Curt Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching