Trailer Hitch Needed for a 2008 Ford F-350 is a Stake Bed Truck with Rear Liftgate
Question:
Good evening, I have a 2008 Ford F350 Stake Bed Truck with a Thieman General Purpose Liftgate Model TT-16RMET - 1600 pound capacity. Do you have any suggestions on how I can add a trailer hitch to pull a trailer. I need to pull a tractor about 2000 lbs on a trailer, carry hay, and general farm use with the trailer. Thank you,
asked by: Bill C
Expert Reply:
Since your 2008 Ford F-350 is a Stake Bed Truck you will need to look at the trailer hitches that fit an F-350 Cab and Chassis. I have linked our selection for you to filter through.
The most popular choice is the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25122. It is a Class V hitch with a 2" receiver that has a Gross Towing Weight (GTW) rating of 16,000 lbs and a Tongue Weight (TW) rating of 1,600 lbs. B&W is well known for the quality of their products that are made right here in the USA.
Although we haven't test fit this hitch on your F-350 specifically, I can tell you that the rear most mounting hole is about 12 inches away from where the rear most edge of the receiver is (see attached picture). Since this is a custom fit trailer hitch you can use that measurement to help determine if it will work out for you or not.
Product Page this Question was Asked From
B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 1600 lbs TW
- 16000 lbs GTW
- 16000 lbs WD GTW
- 2 Inch Hitch
- 1600 lbs WD TW
- Visible Cross Tube
- B and W
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Q&A: Mounting Hole Dimensions of the B and W Hitch part # BWHDRH25122
- Article: How to Choose the Right Trailer Hitch Class
- Video: Trailer Hitch Installation - 1986 Chevrolet C/K Series Pickup - B&W
- Video: Curt Gooseneck - Below the Bed - C60713 Review
- Q&A: Can The B&W Heavy-Duty Trailer Hitch BWHDRH25122 Clear An Aftermarket Bumper On A 1986 Chevy K20?
- Q&A: Class V Trailer Hitch for 1972 Ford F250 with Barden Bumper
- Q&A: Mounting Hole Dimensions for B&W Heavy-Duty Trailer Hitch Receiver, part # BWHDRH25122
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Bulldog Winch Big Dog Hook for 2" x 2" Hitches - Steel
- Q&A: Dimensions of Draw-Tite Ultra Frame Trailer Hitch Receiver # 41947
- Q&A: What is the Width of the Horizontal Plates That Mount to the Vehicle Frame on the Draw-Tite 41947
- Q&A: Bolt Spacing Dimensions B and W Hitch for 2001 Ford Cab and Chassis Truck
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Search Results: 13902
- Search Results: bulldog winch
- Search Results: universal receiver hitches class 3
- Search Results: 2 hitch pin
- Video: Master Lock Hitch Pins and Clips - Standard Hitch Pin - ML1465DAT Review
- Video: Bulldog Winch Off Road Accessories - Tow Hook - Loop - BDW20182 Review
- Video: Master Lock Pivot Lock Hitch Pin Review
- Video: Gen-Y Iron Grip Anti-Rattle Hitch Pin Review GY39FR
- Shop: Front Mount Hitch
- Article: My Trailer Hitch Doesn't Fit
- Shop: Suspension Enhancement
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring