Recommended 4-Way Wiring Harness And Trailer Hitch for a 2022 Kia Forte

Question

Question:

Will this hitch fit on my 2022 Kia Forte?

asked by: Robyn

0

Expert Reply:

Yes, the Curt Trailer Hitch Receiver # C55HR will fit on your 2022 Kia Forte!

This trailer hitch has a maximum towing capacity of 2,000-lbs, a maximum tongue weight of 200-lbs, and has a 1-1/4" x 1-1/4" class I hitch opening.

You are also going to need a set of wiring, like the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C54ER.

This wiring harness will plug into your vehicle's factory OEM wiring harness and will provide your vehicle with a 4-way flat connector.

expert reply by: Bryce D

0

Answer 1

Yes. With the only hitch we carry for your 2022 Kia Forte, the Curt Hitch - 1-1/4" #C55HR, there is a bit of drilling required for installation. The instructions require you to drill out the rear mounting holes on the bottom of the frame rails.…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver #C34UR that you purchased for your 2022 Toyota Corolla will only fit a 2020 - 2022 Toyota Corolla Sedan. For your 2023 Kia Forte you'll need the Curt Trailer Hitch Receiver #C55HR instead. This has different…

view full answer...

Answer 3

The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part #C54ER, has a plug behind the sidewall of the driver-side. It is not in the trunk because it is behind the sidewall. Unfortunately, we do not have a video of this…

view full answer...

Answer 4

The Curt Hitch item #C55HR weighs 25 lbs. This hitch is custom fit for the 2024 Kia Forte's and installs with included hardware. This is a class I hitch with a 1-1/4" receiver. It has a 2,000 lbs towing capacity and a 200 lbs maximum tongue…

view full answer...

Answer 5

The best hitch for your 2023 Kia Forte Sedan is going to be the Draw-Tite Trailer Hitch item #DT83MR. This hitch is custom fit and bolts to your Kia with included hardware. This is a class I hitch, with a 1-1/4" receiver, that weighs 32 lbs. It…

view full answer...

Answer 6

The item you selected, Tow Ready Custom Fit Vehicle Wiring, part #118505, plugs in-line with the vehicles tail light connectors. You will need to access the wiring behind the tail light by removing the plastic trim pieces inside the vehicle. The…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...