What Kind Of Metal Is The Stromberg Carlson Campfire Grill Made Of?

Question

Question:

Is the grill grate stainless, or just chrome plated steel?

asked by: Marnie O

0

Expert Reply:

The Stromberg Carlson Campfire Grill - Stake Mount - Chrome-Plated Steel # GR-1522 is made of chrome plated steel.

The stake itself measures 36" long and is made of black powder coated steel for a clean finish as well as help negate corrosion.

Additionally, the grill measures 15" wide, 22" long, and has a 5-lb weight capacity.

expert reply by: Bryce D

0

Answer 1

I do have an option for you but we don't offer any replacement parts for the Stromberg Carlson Stake and Grill part #GR-1522 except for the Replacement Storage Bag for Stromberg Carlson Stake and Grill part #SC36MR. I'd recommend a complete…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 5

Waylon, it does look like the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is the same thing as the Dexstar 17-233 wheels you're referring too. These are silver wheels with a 6 on 5 1/2 bolt pattern, a 0 offset, and are made in the USA.

view full answer...

Answer 6

While I cannot determine exactly what leaf springs you need I can tell you your Dexter 5,200lb axles uses the Bearing Kit #BK3-300 for each hub. If you can provide me with the serial number on the axles you have I can contact Dexter to verify the…

view full answer...

Answer 7

A cover is available for your Truxedo LoPro QT, it is Replacement Cover for TruXedo Lo Pro QT Soft, Roll-up Tonneau Cover - Black, #TX569101-CVR. This replaces the tarp on your TruXedo Lo Pro QT soft, roll-up tonneau cover #TX569101. It does require…

view full answer...

Answer 8

The Replacement Square End Cap #853-5826 should work perfectly for you. I went out and measured one and found that it's overall diameter is 2 inch by 2 inch and the inner tube piece measures a tiny bit over 1.75 inches by 1.75 inches so it would…

view full answer...

Answer 9

You would need to go by the wiring color guide you have found on your truck. Sometimes we see vehicles use different wire colors than what they commonly will use for a variety of reasons, but since your brake controller wiring comes with a list of…

view full answer...

Answer 10

Your Torsion axle simply has integrated suspension into the axle. It is no different than having a trailer with constant weight on it like a travel trailer to have your 1500 lb UTV stored on it. Your axle is rated at 3500 lbs so it won't be an…

view full answer...

Answer 11

You were on the right track. To raise the tires off the ground for long term trailer storage, the best way is to use your front jack to raise the trailer then place the jack stands under the frame by each axle on all four sides. I have attached a…

view full answer...

Answer 12

I have a solution for you, but the Magnetek PR-7069 is a 30 amp converter and the smallest converter we have is a 35amp converter- which will work just fine and even be a bit faster at charging your battery. I recommend using the Replacement…

view full answer...