Correct Timbren Springs for a 2022 Ford F-150

Question

Question:

i have a 2022 f150 lariat and want to make sure i get the right timbren bump stops for this truck. everything is factory setting. thank you

asked by: Gary G

1

Helpful Expert Reply:

The correct Timbren Rear Suspension Enhancement System for a 2022 Ford F-150 is part # TFR1504E. These will do a great job of helping provide extra rear end support while towing or hauling which in turn reduces sag. They feature a simple bolt-on install and there's no maintenance like with air bags. These are also backed by a lifetime warranty.

expert reply by: Conner L

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 5

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The Stealth Hitches Hidden Rack Receiver item #391KIATELL20 you were looking at would be a great option if you do not want to see the hitch at all when you're not using your Yakima EXO system. It has been confirmed to fit the 2023 Kia Telluride…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Hey Karen, you'll need a specific adapter but the answer is yes, you can use a 1-1/4 inch to 2 inch adapter for your bike rack on your 2017 Ford Fusion with the Draw-Tite Sportframe Trailer Hitch Receiver #24897. What you will need is one…

view full answer...

Answer 11

Hey Carl, thanks for writing in, and that's a good question. Thankfully, the answer is no, you do not need to cut or trim the fascia/face plate on a 2024 Ford Maverick to install the Demco base plate that fits, which is the following part number:…

view full answer...

Answer 12

The instructions for the Demco Tabless Base Plate Kit #DM77YV are being added to page but I'll also send them to you separately. In the instructions they only show that the air dam needs a chunk cut out and that the shutters would remain. The…

view full answer...