Replacement Fold Away Coupler Hinge Kit For Trailer

Question

Question:

need 1/2 x 6 in

asked by: Dennis R

0

Expert Reply:

Though we do not have any pivot pins that are 1/2 inch x 6 available we do have another option for you. The best option that we have would be to replace your coupler with one of our Fold-Away Coupler Hinge Kits. We have the following options:

3 inch x 5 inch Trailer Tongue: Fulton Fold-Away Coupler Hinge Kit # FHDPB350101

3 inch x 3 inch Trailer Tongue Fulton Fold-Away Coupler Hinge Kit # FHDPB330301

2 in x 3 inch Trailer Tongue Fulton Fold-Away Coupler Hinge Kit # FHDPB230101

All three kits have a bolt-on installation and have a sturdy steel construction and is corrosion-resistant. I attached a review video link below.

expert reply by: Noah E

0

Answer 1

To use the Fulton Fold-Away Coupler Hinge Kit #FHDPW230300 on a trailer frame that is 2 by 2 inch will require a 1 inch spacer get welded to the trailer frame by a qualified fabricator to take up the 1 inch of space since this is designed for a 2 by…

view full answer...

Answer 2

I cannot speak for all fold-away coupler hinge kits but the ones we offer, the Fulton Fold-Away Coupler Hinge Kit part #FHDPB230101, part #FHDPB330301, and part #FHDPB350101 do not contain any bushings. It can be rather difficult to just look at a…

view full answer...

Answer 3

Wire feed welding would be the best welding method to secure the #FHDPW230300 hinge kit to your existing trailer tongue. To install the hinge, you would simply cut the tongue at the point at which you want it to pivot, and then slide the two sides of…

view full answer...

Answer 4

There is no perfect calculation for safety chain length since it all depends on the setup you have. Safety chains should be crossed when attached, and also short enough to keep your coupler off of the ground should your trailer disconnect. They also…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Oddly enough I can't find a decent u-bolt that we carry that would work well for your application.

view full answer...

Answer 12

The overall length of the Fulton hinge kit part #FHDPW330300 is 7-1/2 inches. You should note that since this slips over the frame channels it does not add this length to the tongue of the trailer.

view full answer...