What is Overall Length of Fulton Hinge Kit part # FHDPW330300

Question

Question:

What are the lenth dimensions of the 3”x3” weld on swing away tongue hinge ?

asked by: Deshane S

0

Expert Reply:

The overall length of the Fulton hinge kit part # FHDPW330300 is 7-1/2 inches. You should note that since this slips over the frame channels it does not add this length to the tongue of the trailer.

expert reply by: Jameson C

0

Answer 1

The Inno Fishing Rod Rooftop Cargo Box #IN52FR holds both the rod and the reel. It can carry up to 9 bass rods or 4 large spinning rods up to 9' long. It also features cushions to hold the rods and protect the reels.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 4

Hey George, thanks for reaching out! As long as you aren't towing more than the 3,400 lbs I recommend using the Hidden Hitch by Draw-Tite Trailer Hitch Receiver #DT82GR for your 2023 Volvo XC60 because of the completely removable hitch…

view full answer...

Answer 5

From the top of the B and W Tow and Stow part #BWTS10043B down to the bottom of the unused ball when it is in it's lowest position measures 14 inches. The 7 inch drop version part #BWTS10040B instead has this distance at 12 inches.

view full answer...

Answer 6

Thanks for all of the info on your axle as well as the sticker! From that I can easily help you with an idler hub replacement. For that we have the Dexter #42655UC1 which fits your axle and also has the bolt pattern you want of 6 on 5-1/2 inches. I…

view full answer...

Answer 7

The Weld-On Fulton Fold-Away Hinge Kit for 3" x 3" Trailer Tongue, item #FHDPW330300, is constructed of cast steel. All welding must be performed by a certified AWS welder. Making sure casting is straight and fully seated on the…

view full answer...

Answer 8

What you would need is the #FHDPW330300. This is a hinge for a 3 by 3 inch trailer tongue. You'd need to have a welder put 1/4 inch spacers above and below the tube so that it fits yours that is only 2-1/2 inches tall.

view full answer...

Answer 9

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need…

view full answer...

Answer 10

For your aluminum trailer with a galvanized steel tongue (swing-away tongues cannot be used on aluminum tongues), you'll need a die-cast steel tongue with a zinc finish from Fulton. The correct fit is going to depend on the size of your…

view full answer...

Answer 11

The Dexter Zinc-Plated Brake Actuator #T47457007K does not have an access hole to insert a screwdriver to bleed the master cylinder. You will have to use the old method with a 2x4 and the safety chains. While the trailer is disconnected from the…

view full answer...

Answer 12

For a 3x4 inch frame the best hinge kit would be the part #FHDPB350101. This is for a 3 x 5 inch frame but you could have 1/2 inch spacers welded to either side of the channel and it would and work just fine.

view full answer...

What is Overall Length of Fulton Hinge Kit part # FHDPW330300

Product Page this Question was Asked From

Continue Researching