Replacement Landing Gear Lead Leg for Venture VMC900L

Question

Question:

Hello, I have a lead leg landing gear that needs to be replaced on my 2007 challenger keystone only numbers I can find on it are vmc900L-232125 . Was hoping you could steer me in the right direction for a replacement. Thanks

asked by: Eric S

0

Expert Reply:

According to our information you'll need the Replacement Lead Leg # LC119102 for your Venture VMC900L landing gear kit. If you end up needing the follow leg as well that can be found on our site as part # LC119101.

Attached is a review video for you to check out.

expert reply by: Jon G

0

Answer 1

Since your Venture leg is the follow leg the repair kit is #LC146060. If you had the lead leg it would be #LC146059.

view full answer...

Answer 2

The internal parts (screw and nut) on your Venture landing gear are not available as replacement parts but we may have a replacement leg. We carry several legs that could potentially work. Lead: #LC119102 (outer tube is 29-1/2 inches overall)…

view full answer...

Answer 3

Since you already have the B&W Companion Gooseneck-to Fifth-Wheel Hitch you will need the flatbed base #BWRVB3055 to move your traditional Companion to a flat bed truck. If you do not already have a B&W Turnoverball Gooseneck hitch in…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Good news! I was able to go out to the warehouse and measure the etrailer landing gear #RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld…

view full answer...

Answer 12

The airbags that I recommend for your 2018 Ford F-250 are the Air Lift LoadLifter 5000 Air Helper Springs part #AL57399. These airbags will not interfere with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1116 as you can see…

view full answer...