Parts Needed to Add Brakes to 2018 Carry-On Trailer

Question

Question:

My trailer does not have brake flanges. I am thinking a full axle may be necessary. I see dexter axles that may do the trick. I do not see with the self-adjusting brakes. Is there a replacement axle for the 3K7258 with self-adjusting or no.

asked by: Darren V

0

Expert Reply:

Based on what I have found, the 3K7258 axle is a standard 3,500 lb axle. To add brakes to your Carry-On trailer you will need the following:

-Hub and Drum Assemblies: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles # AKHD-545-35-EZ-K

-Brake Assemblies: Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA

-7-Way Wiring: Hopkins 7-Way Molded Trailer Wire Connector # HM20048 (If you want a junction box use # 3375601101)

-Breakaway Kit: Hopkins Engager Push-To-Test Trailer Breakaway Kit # 20400

If you don't have a brake controller for your vehicle I recommend the Redarc Tow-Pro Liberty Brake Controller # RED52VR. This mounts out of sight with only the control knob visible in the cab of your vehicle. If you let me know what vehicle you have I can see if a custom wiring harness is available for installation.

expert reply by: Robin H

0

Dexter Axle 3K7258
(click to enlarge)

Darren B.

11/22/2022

My trailer does not have brake flanges. I am thinking a full axle may be necessary. I see dexter axles that may do the trick. I do not see with the self-adjusting brakes. Is there a replacement axle for the 3K7258 with self-adjusting or no.

Reply

Robin H.

11/22/2022

Thank you for the picture of the axle tag. Your 2018 Carry-On trailer axle has a hub face measurement of 72" and a 58.5" spring center length. When replacing the axle, in addition to the capacity it is important to match the hub face length to what you currently have. I do have a solution for you, but unfortunately we don't have a 72" 3,500 lb replacement axle. The first option is to add a brake flange to your existing axle using the Brake Mounting Flange for 2-3/8" Round Axle # 4-35. This requires a special jig for installation so you will need to take it to a certified welder with the proper tools for installation. The other option is the Timbren Axle-Less Trailer Suspension System # ASR3500S05. This system would replace your axle and leaf springs which would upgrade your suspension. This system fits any frame width so you don't have to worry about matching your current axle length. This will work with the previously mentioned hubs and brake assemblies or you can get the # A35RS545E which includes them.

Reply

Answer 1

The Bulldog Winch Booster Cable Set part #BDW20197 is composed of the Bulldog Winch Booster Cable Set part #BDW20298 and the Bulldog Winch Front Wiring Kit part #BDW20205. Therefore, it sounds like you are just looking for the Bulldog Winch Front…

view full answer...

Answer 2

Yes, the Superwinch Winch 2 Go Portable Winch - Wire Rope - Hawse Fairlead - 4,000 lbs #SW1140222 has the ability to reverse the motor. The line can be electronically pulled out or pulled in with the touch of the switch/remote. This is ran off of a…

view full answer...

Answer 3

Since the Bulldog Winch Booster Cable Set - Quick Connect to Clamp #BDW20298 is rated for up to 2,000-amps this'll work just fine with a 10,000-lbs-12,000-lbs winch like the Bulldog Winch Trailer Winch - Wireless Remote - Wire Rope…

view full answer...

Answer 4

I reached out to my contact at Bulldog Winch, and confirmed that the length of the Bulldog Winch Booster Cables with Quick Connect, #BDW20298, is 20 feet.

view full answer...

Answer 5

Trailer tires should always be inflated to the maximum air pressure indicated on the tire. The tire on tire and wheel combo #AM30620 for example should be at 90 psi. The reason that you inflate trailer tires to the max is because trailer tires are…

view full answer...

Answer 6

The Derale Replacement Push-In Radiator Probe for Derale Single-Stage Thermostat Fan Control, part #D16736, is a thermostatic probe that is inserted into the vehicles radiator and connects to a thermostat switch. The probe will register the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...